User manual OVISLINK AIRLIVE WL-5430AP

[. . . ] AirLive WL-5430AP Wireless Access Point User's Guide 1. 0 Introduction This document is the user's manual for the OvisLink AirLive WL-5430AP. Quick Start The default IP address of the AirLive WL-5430AP is 192. 168. 0. 10. The login is "admin" and password is "ovislink". Connect an antenna to the SMA connector closer to the LEDs. [. . . ] Entered in the format specified by the WEP Length and Mode fields. Select default WEP key from Keys 1-4. Key 1-4 Default Tx key Figure 11: WPA Configuration Table 4: AP Mode -- WPA Configuration Field WPA Data Encryption Authentication Method WPA Passphrase Group Re-Key Time Description Select AES or TKIP. Click the Clear button to clear the Passphrase field Group Re-Key interval (seconds) Figure 12: WPA2 Configuration Table 5: AP Mode -- WPA2 Configuration Field WPA2 Data Encryption Authentication Method WPA2 Passphrase Group Re-Key Time Description Select AES. Click the Clear button to clear the Passphrase field Group Re-Key interval (seconds) Figure 13: WPA/WPA2 Mixed Configuration Table 6: AP Mode -- WPA/WPA2 Mixed Configuration Field WPA Data Encryption WPA2 Data Encryption Authentication Method WPA Passphrase WPA2 Passphrase Group Re-Key Time Description Select AES or TKIP. Click the Clear button to clear the Passphrase field WPA2 key provided by the user. Click the Clear button to clear the Passphrase field Group Re-Key interval (seconds) 6. 3 Advanced Settings Access the Advanced Settings page by clicking the Advanced Settings: Setup button from the AP Mode setup page (Figure 10). The Advanced Settings page allows configuration of advanced Radio settings and range extension of the AirLive WL-5430AP in AP Mode by linking it to up to two repeaters. Figure 14: Advanced Settings The following table describes the setup options in detail. Table 7: AP Advanced Settings Field Beacon Interval RTS Threshold DTIM Interval Protection Mode Transmit Rate Preamble Type Connect Repeater Description Beacon interval (in milliseconds) RTS threshold (Bytes) DTIM interval Allows user to force 802. 11g protection (RTS/CTS) mode off. Selects the transmit rate: Auto or a fixed rate Selects short preamble, long preamble, or Auto Enable/Disable the use of a Repeater (WDS Repeater mode only). Repeater MAC Address MAC address for each Repeater. Up to two Repeaters may be connected. 6. 3. 1 Connect Repeater Up to two Repeaters may be connected. Select Enable for the "Connect Repeater" field. Enter the MAC address for each Repeater in the "Repeater MAC Address" field. 6. 4 Access Filter Click the Access Filter: Setup button from the AP Mode setup page (Figure 10) to access the Access Filter page. The Access Filter page allows the user to configure the AP to allow or deny association to itself based on the MAC address of the client. Up to 32 MAC addresses can be added to the list. Figure 15 and Table 8 detail the options. Figure 15: Access Filter Settings The following table describes the setup options in detail. Table 8: AP Access Filter Settings Field MAC filtering Filter Mode Filter List MAC addresses Description Enables/Disables MAC filtering mode Provides the option to allow or deny clients with MAC addresses listed Up to 32 MAC addresses can be listed. Repeater Setup To configure the AirLive WL-5430AP in Repeater Mode, select Repeater from the Mode page (Figure 9), allow the board to reboot, and click the Repeater: Setup button. Figure 16 and Table 9 show the Repeater Mode setup options. · To select a Repeater Mode, choose WDS Repeater or Universal Repeater in the Repeater Type field. · To set up a WDS Repeater, enter the MAC address of the Parent AP/Router (to be connected to the Repeater) in the Parent MAC Address field. To link an additional repeater, check the Enable Linked Repeater box and enter the MAC address of the additional repeater in the field provided. [. . . ] Table 19: PMP Advanced Settings Field RTS Threshold DTIM Interval Protection Mode Transmit Rate Preamble Type Description RTS threshold (in bytes) DTIM interval Allows user to force 802. 11g protection (RTS/CTS) mode off. Selects the transmit rate: Auto or a fixed rate Selects short preamble, long preamble or Auto 10. Client Mode Setup 10. 1 Basic Setup To configure the AirLive WL-5430AP in Client Mode, select Client from the Mode page (Figure 9), allow the board to reboot, and click the Client: Setup button. Figure 21 and Table 20 describe the Client Mode setup options. [. . . ]