User manual PACKARD BELL I XTREME 9910 STELLA CHASSIS DISASSEMBLY MANUAL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PACKARD BELL I XTREME 9910. We hope that this PACKARD BELL I XTREME 9910 user guide will be useful to you.

Lastmanuals help download the user guide PACKARD BELL I XTREME 9910.


Mode d'emploi PACKARD BELL I XTREME 9910
Download
Manual abstract: user guide PACKARD BELL I XTREME 9910STELLA CHASSIS DISASSEMBLY MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] Label all removed connectors; note where the connector goes and in what position it was installed. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the chassis. [. . . ] 2: Removing the left side cover screws Carefully slide the side cover towards the back of the chassis. Lift the side cover out and away from the chassis. 3: Removing the left side cover To remove the right side cover, first remove the rear bezel (see section Removing the Rear Bezel) and then perform the following steps: 1. Carefully slide the side cover two centimetres towards the front of the chassis. Lift the side cover out and away from the chassis. To remove the front bezel, first remove the rear bezel (see section Removing the Rear Bezel), remove the left side cover (see section Removing the Left Side Cover), and follow the steps below: 1. Gently unlock the three lateral latches that hold the front bezel and pull it away to the opposite side. To remove the drive bracket containing the DVD/CD-ROM drive and the floppy disk drive, first remove the rear bezel (see section Removing the Rear Bezel), remove the left side cover (see section Removing the Left Side Cover), remove the front bezel (see section Removing the Front Bezel); then follow the steps below: 1. Disconnect all power and data cables from the drives installed. Unlock the drive bracket by pressing the upper and lower latch and slide the bracket out of the chassis. To remove the DVD or CD-ROM drive, first remove the rear bezel (see section Removing the Rear Bezel), remove the left side cover (see section Removing the Left Side Cover), remove the right side cover (see section Removing the Right Side Cover), remove the drive bracket (see section Removing the Drive Bracket); then follow the steps below: 1. Slide the drive towards the front out of the bay. To remove the floppy disk drive, first remove the rear bezel (see section Removing the Rear Bezel), remove the left side cover (see section Removing the Left Side Cover), remove the right side cover (see section Removing the Right Side Cover), remove the drive bracket (see section Removing the Drive Bracket); then follow the steps below: 1. Slide the floppy disk drive towards the front out of the bay. To remove the hard disk drive, first remove the rear bezel (see section Removing the Rear Bezel) and remove the left side cover (see section Removing the Left Side Cover), remove the front bezel (see section Removing the Front Bezel); then follow the steps below: 1. Carefully disconnect the four-wire power cable and the flat data interface cable from the hard disk drive. Remove the screws in the front of the chassis holding the hard disk drive bracket to the chassis. Remove the screw on the side of the hard disk drive bracket holding it to the drive bracket above (see Fig 6 in section Removing the Drive Bracket). [. . . ] Note: When reassembling the power supply unit, make sure that the voltage selector switch is set correctly before connecting the system to a power strip (surge protector) or grounded AC electrical outlet. If the switch is set incorrectly, the system could become seriously damaged. The information in this guide is subject to change without notice. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PACKARD BELL I XTREME 9910

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PACKARD BELL I XTREME 9910 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag