User manual PALSONIC TFTV385

[. . . ] OWNER'S MANUAL 38CM CORDLESS REMOTE LCD TV/MONITOR MODEL: TFTV385 N111 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulation on your purchase of this LCD TV We recommend that you read this manual thoroughly before use to fully enjoy the many functions and excellent features of this unit. Keep this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual model. Contents Index Important Safety Cautions . . . . . . . . . . . . . . . . . . . . . 1 Identification of controls . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you select S-video signal, please set the input signal source of LCD TV to SVIDEO mode. Note: S-Video is a signal format which transfers the colour and brightness of the picture with higher quality than a Composite connection. The S-Video signal connection is recommended to produce the best picture. If so, connect the cables to like colours. 14 Basic Operations Turning on 1 POWER Connect the power correctly, then the red indicator lights up and the unit is in STANDBY mode. Press the POWER ( ) button on the remote control or on the unit to turn on the TV set. The indicator will turn to yellow. 2 CH VOL - VOL + CH EXIT Turning off MENU 1 2 With the power on, press the POWER ( ) button to turn off the TV and the TV is in STANDBY mode, the indicator will turn to red. If you want to turn off the power completely, unplug the power cord from the wall outlet. C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP 1 4 7 2 5 8 0 3 6 9 -/-- Note: Do not switch the on/off state of the unit quickly. The interval of the turning on and turning off should be more than 5 seconds. Selecting input signal 1 Press the SOURCE button on the unit or button on the remote control. The screen displays the menu as shown on the right. Press CH to highlight your desired input signal source. Press VOL+/- or wait for about 4 seconds and the desired signal source will be selected. 2 Note: All buttons shown in the manual are located on the remote control unless otherwise indicated. 15 Main On-Screen-Display (OSD) introduction TV/AV/S-VIDEO MODE Picture Setting Menu brightness contrast color sharpness tint 50 50 16 32 0 1 2 3 4 5 6 Press MENU button to display menu screen. Press EXIT button repeatedly to exit the menu. YPbPr / RGB MODE Picture Setting Menu brightness contrast 50 60 color temp 5000K 7300K 9300K user customer temp setting System Setting Menu blue screen backlight scaler mode color sys. sleep time fill all Auto I 10 minutes on 6 System Position Menu h position v position frequency phase 50 50 866 15 Audio Setting Menu SRS bass treble balance AVC off on off 0 0 0 Audio Setting Menu SRS bass treble balance AVC off on off 0 0 0 Channel Setting Menu channel number skip manual search auto search fine tune channel edit off 9 on System Setting Menu sleep time back light 20 minutes 6 OSD Setting Menu OSD Setting Menu language OSD position language OSD position OSD background OSD timeout opaque translucent English OSD background OSD timeout 30 seconds opaque translucent English 30 seconds Signal Information Menu Signal Information Menu video type: PAL / 50Hz mode: 3 resolution: 640 x 480/60Hz mode: 40 Note: in AV/S-VIDEO mode, Channel Setting menu can not be accessed and in System Setting menu some menu items (such as color sys. menu item) is grey and can not be adjusted. 16 Operations Channel Setting There are two ways to preset channels: to preset channels automatically and to preset channels manually. Below we will describe how to preset the channels by making use of the menu. POWER Auto Search CH VOL 1 Access Channel Setting menu. VOL channel number skip off 9 on - + CH EXIT MENU 2 Press CH Search. manual search auto search fine tune channel edit C. SYS ZOOM CLK SLP button repeatedly to highlight auto search item. 3 Press VOL+/- to start Auto AUTO. ADJ P. M DSP VHFH Searching 20 65MHz 1 4 7 2 5 8 0 3 6 9 -/-- All active channels will be preset and stored into the memory automatically. During the process of Auto Search, pressing MENU will stop the process. Manual Search If Auto Search can not preset the desired channels, or you want to preset the desired channels one by one with the preferred channel numbers, please make use of Manual Search. 1 Use channel select buttons to select a channel number. channel number 9 on 2 Access Channel Setting menu. 3 Press CH button repeatedly to highlight manual search item and press VOL+ to enter. skip manual search auto search fine tune channel edit off VHFH Searching 15 65MHz 4 Press VOL+ or VOL- button to perform the searching. When a channel is located, the searching stops, this channel is then memorised with the preset channel number. 17 Operations Channel Setting To skip unnecessary channel After presetting the channels, you can skip unnecessary channels so that only the channels you want to watch are selected when you press the CH to change channels. POWER 1 CH VOL Select the channel number which you want to skip using the keypad. to select skip channel number skip off 9 on - VOL + CH EXIT 2 3 4 MENU C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP Press VOL+/- to select on. Now when you press CH to change channels, this channel will be skipped. manual search auto search fine tune channel edit 1 4 7 2 5 8 0 3 6 9 -/-- If you want to resume a skipped channel, use the keypad buttons to enter the channel, then access the Channel Setting menu and select skip, press VOL+/- to set skip off. When you press CH to change channels, the channel will be present. Fine tuning Fine tuning is not necessary under normal conditions. However, in area of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use Fine tuning. 1 2 Access the Channel Setting menu. channel number skip off 9 on Press CH button repeatedly to highlight fine tune item. manual search auto search fine tune channel edit 3 Press VOL+/- to fine tune to achieve best picture and sound. VHFH Fine Tuning 22 75MHz 18 Operations Channel Setting Channel edit You can edit the channel programs in your favourite order. POWER 1 CH VOL Access the Channel Setting menu. Press VOL+/- to enter into the sub-menu. [. . . ] The value you set will be stored . 5 27 Troubleshooting Before calling for service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms Ghost or double images Check item This may be caused by obstruction to the antenna due to high rise buildings or hills. Using a highly directional antenna may improve the picture. Check that the AC power cord is plugged into the mains socket. [. . . ]