User manual PANASONIC AJ-D250P

[. . . ] Digital Video Cassette Recorder AJ- P Operating Instructions ON OFF POWER DIGIT EJECT AL VIDE INPUT LINE S-VIDEO O CASS ETTE SELECT DIO REC LEV ELE CH1 dB OPTION AU BEGIN END Digital Video Cassett e Record er - LOCAL MENU REMOTE AUDIO OUT SELECT CH3 CH4 CH1 CH2 CH2 REC INH REMOTE -30 -25 -20 -16 WIDE -12 -8 DV -4 0 CTL TC UB SERVO HOURS MINUTE S SEC ONDS FRAMES REW MODE STOP DOWN MENU FF UP PLAY | DATA PAUSE/ STTIL + REC SET RESET COUNTE R REMO TE Printed in Japan VQT8188-2 S0699W3119 A P IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. [. . . ] Set the item to the COLOR mode with regular color signals. OIf color signals are recorded in the B/W mode, the pictures will be abnormally colored when the signals are played back. For selecting the processing to be performed in the event that LOW-RF has occurred or the servo lock has been disengaged during playback. N-MUTE 0: The video signals are not muted. For selecting ON or OFF for the closed capture signals in the first field. BLANK 0: Forcible blanking THRU 1: No blanking For selecting ON or OFF for the closed capture signals in the second field. BLANK 0: Forcible blanking THRU 1: No blanking For selecting the freeze mode of the still pictures in the PLAY PAUSE or frame advance mode. FIELD 0: Field freeze FRAME 1: Frame freeze For selecting the process for detecting the input signal frames. FORCED 0: The frames are detected at all times. AUTO 1: Frame detection is inhibited only with non-standard signals. For selecting the video signal processing. AUTO 0: The mode corresponding to the input is automatically established. NSTD 1: The non-standard mode is forcibly established. For selecting the setup level when input composite signals are to be converted into component signals and recorded. THRU 0: The input signals are recorded as they are. CUT 1: The signals are recorded after removing the 7. 5% setup. For selecting the setup level when playback component signals are to be converted into composite signals and output. THRU 0: The playback signals are recorded as they are. ADD 1: The signals are recorded after adding the 7. 5% setup. 601 V-MUTE SEL 0000 0001 602 CC (F1) BLANK 0000 0001 603 CC (F2) BLANK 0000 0001 604 FREEZE SEL 0000 0001 605 IN FRM DET 0000 0001 606 STD/NSTD SEL 0000 0001 607 VIN SETUP 0000 0001 608 VOUT SETUP 0000 0001 The underlining denotes the factory mode setting. 33 Setup Menus AUDIO menu Item No. 700 Superimposed display AUDIO EDIT IN 0000 0001 701 AUDIO EDIT OUT 0000 0001 702 PB FADE 0000 0001 0002 703 SEARCH CUE 0000 0001 704 DV PB ATT 0000 0001 705 CUE INSERT 0000 0001 No. Setting Superimposed display Description of setting For selecting the joining method at the IN point during digital audio editing. CUT 0: Cutting FADE 1: Fading For selecting the joining method at the OUT point during digital audio editing. [. . . ] 4 Use the Phillips head screwdriver to push in and turn the red plastic screw part counterclockwise once more. Again rotate the flange part of the supply reel in the take-up direction to take up the tape slack. This two-step procedure needs to be repeated until the tape is completely housed in the cassette case (about 90 turns of the red plastic screw part). 5 Use the Phillips head screwdriver to turn the red plastic screw part at the slot-in side clockwise to eject the cassette tape. [. . . ]