User manual PANASONIC CQ-C8200

[. . . ] It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly. CD Player/Receiver Observe the following cautions when using this unit. Keep the sound volume at an appropriate level. Keep the volume level low enough to be aware of road and traffic conditions while driving. Model: CQ-C1123NW/C1113NW/C1103NW Operating Instructions Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or fire. CAUTION LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. First Time Power On Model: CQ-C1323NW/C1313NW/C1303NW Caution leads by winding them with vinyl tape or similar protection. Label Indications and Their Locations CLASS 1 LASER PRODUCT Use the designated parts and tools for installation. your car's 1 SetON position. ignition switch to the ACC or ACC ON 2 Press [SRC] (PWR: Power). Do not block the air vent or the cooling plate of the unit. Laser Product This pictograph intends to alert you to the presence of important operating instructions and installation Warning instructions. [. . . ] Down Hold down [4] (RANDOM) for more than 2 seconds. Hold down again to cancel. Press [5] (SCAN). Press again to cancel. CQ-C1323NW CQ-C1313NW CQ-C1303NW Disc Player (CD-DA disc): Previous/next track CQ-C1323NW Previous/next file CQ-C1313NW CQ-C1303NW Repeat play The current song (track/file) is repeated. Folder scan play (MP3) From the next folder, the first 10 seconds of the first file on each folder is played in sequence. Disc Player (MP3 disc): Preset station selection Press the corresponding preset button from [1] to [6] to tune into a preset station. Press [6] (REPEAT). Press again to cancel. Hold down [5] (SCAN) for more than 2 seconds. Hold down again to cancel. Troubleshooting If You Suspect Something Wrong Check and take steps as described below. If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service Centre. The product should be serviced only by qualified personnel. Please refer the checking and the repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking. Note: For whatever is printed in italics in "Check point" column, Conduct the operations and checks by yourself. Radio Data System (RDS) in FM Broadcasting ¡ Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause ignition or electric shock. Immediately stop using the unit and consult your dealer. (a "Function Settings") 1 Press [VOL] (PUSH SEL) to display the audio menu display. PTY On/Off Holding down [DISP] (PTY) for more than 2 seconds toggles PTY mode on and off. 1 Hold down [VOL] (PUSH SEL) for more than 2 seconds to display the function menu display. Note: If no operation takes place for more than 5 seconds in the function menu, the display returns to the regular mode. Common Start the engine. (Or turn the ignition switch to the ACC position. ) Verify the wiring. (battery lead, power lead, ground lead, etc. ) Fuse blown (Contact the nearest Panasonic Service Centre. ) Ask a professional for fuse replacement. Wait until the dew disappears before turning on the unit. Radio Detailed PTY Selection Note: If no operation takes place for more than 5 seconds in the audio menu (2 seconds in Main volume adjustment), the display returns to the regular mode. What is RDS? Frequent noise No power Tune in to another station of high-intensity waves. Make sure that the antenna mounted point is grounded properly. The preset memory is cleared to return to the original factory setting when the power connector or battery is disconnected. Other functions of RDS CT (Clock Time) The clock is automatically adjusted. 1 Press []] or [[] to select PTY. SPEECH INFO CULTURE ROCK M OTHER M SOCIAL LEISURE OLDIES / / / / / / / / MUSIC / SPORT / SCIENCE / EASY M / WEATHER/ RELIGION / JAZZ / FOLK M / NEWS / EDUCATE / VARIED / LIGHT M / FINANCE / PHONE IN / COUNTRY / DOCUMENT AFFAIRS / DRAMA / POP M / CLASSICS / CHILDREN / TRAVEL / NATION M / 2 Press [VOL] (PUSH SEL) to select a mode to be adjusted. Volume (Setting Range: 0 to 40, Default: 18) 3 Turn [VOL] clockwise or counterclockwise to adjust. 2 Press [VOL] (PUSH SEL) to select a mode to be adjusted. FM Monaural FM 3 Turn [VOL] clockwise or counterclockwise to adjust. MONO OFF PS (Programme Service Name) As well as the frequency, the name of the broadcast station appears. Programme Search by PTY Programs can be searched for by use of PTY that has been originally preset. Preset data deleted q : Up w : Down Noise is significantly decreased when weak signals are received from an FM broadcast station. (Default: OFF) MONO ON ( lights. ) LOCAL OFF EON (Enhanced Other Network) RDS information is updated constantly in response to the current position. Press [1] to [6] to select PTY in the PTY mode. 1 2 Programme Type NEWS SPEECH Contents NEWS AFFAIRS, INFO, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT SPORT POP M CLASSICS ROCK M, EASY M, LIGHT M, OTHER M, JAZZ, COUNTRY, NATION M, OLDIES, FOLK M Bass (Setting Range: ­12 dB to +12 dB by 2 dB, Default: 0 dB) FM Local q : Increased w : Decreased FM No sound Error Display Messages (The disc is ejected automatically. ) The disc is dirty, or is upside down. Check the disc. TA (Traffic Announcement) The following functions are available when the TA mode is active ( lights). ¡ A TP station is automatically searched for and received at the instant of toggling the TA mode on if you are receiving a non-TP station or TP station with poor reception. [. . . ] Sluit de luidsprekers als volgt aan. Precautions (ISO Connector) The pin arrangement of the power connector conforms to ISO standard. Please check that the pin arrangement of the connector in your car conforms to ISO standard. For car types A and B, change the wiring of the red and yellow leads as shown at below. After connection, insulate the portions marked () with insulating tape. [. . . ]