User manual PANASONIC CQ-DF701W

[. . . ] CD Player/Receiver with Dot Matrix LCD and CD Changer Control CQ-DF701W REMOTE SET/AUTO·P ;/1 CQ-DF701W MOSFET BAND 50WX4 OPEN DISP VOL MENU P·SET CH·C !@ D·M PWR TUNE TRACK DISC MUTE S·HDB SOURCE Operating Instructions DIM HDB CD RECEIVER WIITH FULL DOT MATRIX DISPLAY Please read these instructions carefully before using this product and save this manual for future use. E N G L I S H Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. Use this Product Safely When Driving Keep the volume level low enough to be aware of road and traffic conditions. Disc Mechanism Do not insert coins or any small objects. [. . . ] When the removable face plate is removed. ( page 33) Security message display Security Function Default: ON S-LED 26 CQ-DF701W CQ-DF701W 27 E N G L I S H 19 Installation Guide Identify All Leads WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. Speakers Identify the car speaker leads. There are two leads for each speaker which are usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 20 Installation Hardware No. 1 2 3 4 5 6 7 8 Item Mounting collar Hex. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Removable face plate case Trim plate Diagram Q'ty 1 1 1 1 1 1 1 1 If you encounter problems, please consult your nearest professional installer. [. . . ] Direct the remote control at sensor (REMOTE) on the panel. CD is in the CD compartment but no sound is made, or CD is ejected automatically. Buttons are invalid for operation. Sound skips due to vibration. CD is not ejected. 38 CQ-DF701W CQ-DF701W 39 E N G L I S H 31 Troubleshooting (Continued) Error Display Messages CD Display Cause/Step E N G L I S H CD Changer Display Cause/Step 32 Disc is dirty, or is upside down. Press [OPEN] to open the front panel and press [<] (EJECT). Load the disc again. Disc is dirty, or is upside down. (The changer automatically switches to the next disc. ) POWER OFF After 5 seconds. After 5 seconds. [. . . ]