User manual PANASONIC CQ-DP171U

[. . . ] ® APM FOLDER VOL BAND TUNE TRACK CQ-DP171U CD RECEIVER WITH CHANGER CONTROL PWR SEL DISP SOURCE REMOTE RANDOM SCAN REPEAT MUTE 1 2 3 4 5 6 LOUD Removable Full Front CD Player/Receiver with Changer Control Lecteur CD/Récepteur avec commande de changeur de CD et panneau avant entièrement amovible Reproductor de CD/Receptor con carátula completa desmontable y control de cambiador de CD CQ-DP171U Operating Instructions Manuel d'instructions Manual de instrucciones TEXT ¡Please read these instructions carefully before using this product and keep this manual for future use. ¡Prière de lire ces instructions attentivement avant d'utiliser le produit et garder ce manuel pour l'utilisation ultérieure. ¡Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro. E N G L I S H Safety Information Radio Frequency Interference Statement (Part 15 of the FCC Rules) : Applies only in U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 of the FCC Rules. ¡These limits are designed to provide reasonable protection against harmful interference in an automobile installation. [. . . ] ¡Connect the car wires to the wires of the power connector. ¡Install the unit in the dashboard. If you encounter problems, please consult your nearest professional installer. Dashboard Specifications Thickness Min. 7/32" (5. 56 mm) 2 3/32" (53 mm) 7 5/32" (182 mm) 24 CQ-DP171U Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one : Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows: Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 16 Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If the bulb also turns off and on, that outlet is the car power lead. If your car is not wired for an audio unit : Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. Otherwise you may ignore this procedure. [. . . ] ¡File names entered in lower case will be displayed in upper case. ¡Characters that the player cannot display are shown as an asterisk. Glossary ISO 9660 The most common international standard for the logical format for files and directories. ID3Tag A function that allows character information (title, artist, album title, date, etc. ) to be written onto the disc. (Not supported) APPLE HFS The file system used by the Machintosh operating system to organize data. (Not supported) Packet writing A method of writing data on a CD media in small increments. [. . . ]