User manual PANASONIC CQ-DP33EW

[. . . ] The name of MP3/WMA file should be added by rules as shown in the following descriptions and also comply with the rules of each file system. You may encounter trouble in playing MP3/WMA files or displaying the information of MP3/WMA files recorded with certain writing software or CD recorders. The file extension ". mp3" or ". wma" should be assigned to each file depending on the file format. This unit does not have the play list function. [. . . ] You ran the file in fast forward or fast reverse during playback or turned off the ignition switch of the car during playback. Playing another file will return the file playing time to normal. You played a VBR (Variable Bit Rate) format file. The file playing time of VBR (Variable Bit Rate) format file is sometimes displayed incorrectly. E N G L I S H 22 Sound skips, bad sound quality. caused by noise) Sound skips due to vibration. Disc is not ejected. CD text is not displayed normally. Folder/file name is not displayed correctly. Time is counted but no sound comes out. MP3/WMA Trouble Cause/Step The disc does not conform to any of the file systems supported by this player. Insert a disc that conforms to the file systems (ISO 9660 Level 1, Level 2, Joliet, Romeo or Apple Extension to ISO 9660). The MP3 file is missing the ". mp3" file name extension. Make sure to add the ". mp3" extension to each MP3 file name. The WMA file is missing the ". wma" file name extension. Make sure to add the ". wma" extension to each WMA file name. File playing time is not displayed correctly. 32 CQ-DP33EW CQ-DP33EW 33 E N G L I S H 23 Troubleshooting (continued) Sound Setting Trouble No sound from left, right, front or rear speaker. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. Speakers Identify the car speaker leads. There are two leads for each speaker which are usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. [. . . ] ['] (release button) Contact Place the Removable Face Plate into Case 2 1 Press. (page 42) 3 Gently press the bottom of the case and open the cover. Place the face plate into the case and take it with you when you leave the car. Removable face plate case 2 Pull on the right side of the unit. 2 Remove the trim plate 7 with a screwdriver. 7 Trim plate Screwdriver 1 2 Install Removable Face Plate 1 Slide the left side of the removable face plate in place. Plastic tab 2 1 2 Press the right end of the removable face plate until "click" is heard. plates 3 1 Insert the lock cancelsides of 8 along the grooves on both the main unit until "click" is heard. Cut out 2 Pull out the unit while pushing the plates further inside. 1 Insert. 8 Lock cancel plate Insert the tab end in the outer groove. "Click" 2 Pull out. Caution: This face plate is not waterproof. [. . . ]