User manual PANASONIC CQ-DP745

[. . . ] These limits are designed to provide reasonable protection against harmful interference in an automobile installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experience radio technician for help. [. . . ] Do not attempt to use it in any other system. Before you begin installation, look for the items which are packed with your unit. Warranty Card. . . Fill this out promptly. Panasonic Servicenter for Service Directory . . . Keep for future reference in case the product needs servicing. Installation Hardware. . . Needed for in-dash installation. Control Reference Guide Buttons of the remote control function in the same way as the controls on the main unit of the reference page. Point the remote control unit at the main unit's sensor (REMOTE). (ATT) Required Tools You'll need a screwdriver, a 1. 5 V AA battery, and the following: 12 V DC Electrical Side-cut Test bulb tape pliers Power button (PWR) ( page 10) Mode button (MODE) ( pages 14, 16) PWR MUTE Mute button (MUTE) ( page 10) Volume control buttons (VOL, " #) ( page 10) 8 MODE VOL Overview This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. Connect the car wires to the wires of the power connector. Check the operation of the unit. Band/Disc up* button (BAND/DISC UP*) ( pages 14, 17) *Only for CD changer control (When the CD changer is connected. ) PRG BAND/DISC UP Dashboard Specifications Thickness Min. 7/32z (5. 56 mm) 23/32z (53 mm) 75/32z (182 mm) TUNE TRACK Tune/ Track buttons (TUNE/TRACK, 6 5/ % $) ( pages 14, 16) Car Audio 18 CQ-DF402/DFX302U CQ-DF402/DFX302U 19 E N G L I S H 11 Installation Guide (Continued) Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. Speaker impedance should measure 4­8 , which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage. Motor Antenna Connect the car motor antenna lead to the dark blue motor antenna relay control lead. Battery Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block. Antenna Connect the antenna by plugging the antenna lead into the antenna receptacle. Equipment Connect any optional equipment such as an amplifier, according to the instructions furnished with the equipment. Leave about 12z (30 cm) of distance between the speaker leads/amplifier unit and the antenna/antenna extension cord. Read the operating and installation instructions of any equipment you will connect to this unit. Power Connect the red power lead to the correct car radio wire or to the appropriate fuse port on the fuse block. If the stereo unit functions properly with all these connections made, disconnect the wires and proceed to the final installation. Final Checks 1. Make sure that all wires are properly connected and insulated. [. . . ] Insert discs into the changer (magazine). Left and right sounds are reversed in stereo listening. Notes: There may be cases where the disc numbers affected by an error are displayed before "E1" or "E2". Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the operating instructions for the changer used. CQ-DF402/DFX302U 28 CQ-DF402/DFX302U 29 E N G L I S H 21 Maintenance Care of the Unit Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. [. . . ]