User manual PANASONIC CQ-DP875

[. . . ] Keep screwdrivers and other metallic objects away from the disc mechanism and disc. When Car Washing Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, fire, or other damage. Use Authorized Servicenters Do not attempt to disassemble or adjust this precision product. Please refer to the Servicenter list including with this product for service assistance. C H I N E S E When Parked Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on. For Installation This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30x. Use the Proper Power Supply This product is designed to operate with a 12 V DC, negative ground battery system. Components Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] There are two leads for each speaker which are usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. Ground Connect the black ground lead of the power connector to the metal car chassis. Overview This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. Connect the car wires to the wires of the power connector. If you have difficulties, consult your nearest authorized professional installer for assistance. Installation Procedures First complete the electrical connections, and then check them for correctness. ( page 32) mounting collar 1 Insertthe mounting tabs1 into thea dashboard, and bend out with screwdriver. Make sure that the lock lever (§) is flush with the mounting collar 1 (not projecting outward). Lock lever (§) E N G L I S H 12 Preparation We strongly recommend that you wear gloves for installation work to protect yourself from injuries. When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. Disconnect the cable from the negative - battery terminal (see caution below). Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30o. 6 Power connector Lock lever (§) Mounting tabs 5 Mounting bolt unit. 2 Secure the rear of thebolt 5 and power connector After fixing mounting 6, fix the rear of the unit to the car body by either method (a) or (b) shown below. Less than 30x 3 Insert trim plate 7. 4 After installation, reconnect battery terminal. the negative - Caution: Do not disconnect the battery terminals of a car with a trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. (a) Using the rear support strap 3 Fire wall of car 4 Tapping screw (5 mm·a16 mm) 3 mm· 2 Hex. [. . . ] 500 mA) This lead is not intended for use with switch actuated power antenna. Black Red Dark blue Dark blue/white stripe Speaker lead FRONT SP REAR SP White/black stripe s White r Gray/black stripe s Gray r Green/black stripe s Green r Violet/black stripe s Violet r Radio Trouble Much noise in FM stereo and monaural broadcasts. Cause/Step Station is too far, or signals are too weak. Select other stations of higher signal level. Battery cable is not correctly connected. [. . . ]