User manual PANASONIC CQ-DP975EW

[. . . ] Press [LEVL] (level) to change the level meter display. 2 Press [" VOL] or [# VOL] to change each level. Bass: Adjustable range: j12 dB to i12 dB (by 3 dB step) Hours 2 Press and hold [DISP] (CLOCK) for more than 2 seconds. (Hours blink. ) (Default) Volume level (0 to 40) 3 Press [% TUNE] or [$ TUNE]. (Hours set. ) Minutes 4 Press [DISP] (CLOCK). (Minutes blink. ) Pattern 1 Pattern off Pattern 2 Pattern 3 Pattern 4 Treble: Loudness Press [LOUD] to enhance bass and treble tones at low or medium volume. LOUD Balance: Adjustable range: j12 dB to i12 dB (by 3 dB step) R (right speaker) or L (left speaker) 5 Press [% TUNE] or [$ TUNE]. (Minutes set. ) Press [LOUD] again to cancel. Adjustable range: 1 to 15 (by 1 dB step) Balance center 6 Press [DISP] (CLOCK). (End. ) Note: Press and hold [% TUNE] or [$ TUNE] for more than 2 seconds to change numbers rapidly. Fader: Mute Press [MUTE] to mute the sound completely. MUTE Anti-volume-blast circuit: When the power is switched off and on again, the volume slowly rises to the previous level. The anti-volume-blast circuit will not work when the volume level is set lower than position 20 on the display. F (front speaker) or R (rear speaker) Adjustable range: 1 to 15 (by 1 dB step) Fader center Time Reset Press and hold [DISP] (CLOCK) for more than 2 seconds to activate the time setting mode to reset the time. [. . . ] Refer to instructions for the concerned devices for details. Clean disc, referring to the section on "Notes on CD/CD Media (CDR, CD-RW)". The unit may not successfully play back a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. Refer to instructions for the concerned devices for details. Trouble No sound from right, front or speakers. Do not attach any seals or labels to your discs. Do not write on the disc label in a heavy pen or ballpoint pen stroke. Rough edges Label side Note: There may be cases where the disc numbers affected by an error are designed before "E1" or "E2". Displays and the steps to be taken for errors vary in part from changer to chager. For details, refer to the operating instructions for the changer used. Do not use irregular shaped discs. <Right> <Wrong> Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 14 Installation Hardware No. 1 2 3 4 5 6 7 8 Item Mounting collar Hex. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Removable face plate case Trim plate Diagram Q'ty 1 1 1 1 1 1 1 1 If you encounter problems, please consult your nearest professional installer. Caution: This unit operates with a 12 V DC negative ground auto battery system only. Do not attempt to use it in any other system. [. . . ] Removing this face plate makes the radio totally inoperable. E N G L I S H 18 1 Main unit 1 Open Contact Place the Removable Face Plate into Case 1 Switch off the power of the unit. ( page 26) 3 Gently press the bottom of the case and open the cover. Place the face plate into the case and take it with you when you leave the car. 7 Removable face plate case 45WX4 OPEN [OPEN] 2 Push 3 Pull out RANDOM REP PWR SOURCE 2 Push the face plate to the left. 3 Pull it out toward you. Install Removable Face Plate 2 Remove the trim plate 8 with a screwdriver. [. . . ]