User manual PANASONIC CQ-FX85LEN

[. . . ] Failure to observe this many cause malfunction due to the precise mechanism of this unit. For Installation The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. Your Car Audio system requires a complex installation procedure to ensure reliable operation. If you experience any operational difficulties, or require a repair, please refer to the original installer or your supplying dealer or Panasonic Service Center for assistance. Malfunctions Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. [. . . ] Press [BAND](PRG) to resume the tape play. Pencil Exposed end (Open end) Do not touch or pull out the tape. 26 CQ-FX421/FX321N CQ-FX85LEN Lights when a tape is in the deck PRG AUTO·P E N G L I S H 12 REMOTE CQ-FX85LEN OPEN MONO/LOC VOL SEL BAND PTY PWR TUNE TRACK SOURCE CASSETTE RECEIVER WITH CHANGER CONTROL CT EON PTY CT S·HDB DISC RANDOM SCAN REPEAT REG TA DISP 1 MTL NR 2 3 TPS 4 5 B·S REP 6 AF SUB·W Metal Tape Mode ¡Press [1](MTL) when playing metal or chromium dioxide (CrO2) tapes. ¡Press [1](MTL) again to cancel. MTL Repeat Play ¡Press [6](REP) to repeat the current program. ¡Press [6](REP) again to cancel. REP Note: Playing non-metal tapes in MTL mode causes high frequency imbalance, which affects tone quality. Blank Skip ¡Press [5](B · S) to skip unrecorded portions longer than 15 seconds on the tape. ¡Press [5](B · S) again to cancel. B-SKIP Dolby Noise Reduction ¡Press [2](NR) to set the Dolby B NR mode. ¡Press [2](NR) again to cancel. B Note: Set the Dolby B NR mode when playing back a tape recorded with Dolby B Noise Reduction. Note: When repeat is on, the blank skip does not work because the repeat has priority over the blank skip. Tape Program Search (TPS) Operation q Press [3](TPS) to activate the Tape Program Search mode. w To select a desired program, press [2TRACK] or [1TRACK] corresponding times to go forward (up to 9) or backward (up to 8). (Rewind:) 8t 0 (Fast forward:) 1 s9 Notes: The TPS mode may not work correctly in the following cases. This, however, does not mean that the unit is defective. ¡There is an interval less than 3 seconds or having a high level of noise or hum between programs. ¡There is particularly low-level passage during the program. e Press [3](TPS) again to cancel. CQ-FX85LEN 27 CD Changer Control Basics E N G L I S H 13 Mode Selection Press [SOURCE] to change to the CD changer mode. Source Radio Cassette Tape Player (When a Tape is inserted) VOL PRG AUTO·P REMOTE Track Number Disc Number Playing Time CQ-FX85LEN OPEN MONO/LOC BAND PTY PWR CD changer control (When a CD changer is connected) SEL TUNE TRACK SOURCE CASSETTE RECEIVER WITH CHANGER CONTROL CT EON PTY CT S·HDB DISC RANDOM SCAN REPEAT REG TA DISP DISP 1 MTL NR 2 3 TPS 4 5 B·S REP 6 AF SUB·W Track Selection [fTRACK] : Advance to the next track. [aTRACK] : Back to beginning of the current track. (Press twice) Disc Selection [1] ({DISC): Previous disc. Follow the electrical connections carefully (a Page 34). Failure to do so may result in damage to the unit. Connect the power lead (red) after all other connections are made. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal. Insulate all exposed wires to prevent short circuiting. Secure all loose wires after installing the unit. Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit. (b) Using the Rubber Cushion (Option) Rear Support Bracket (Provided on the car) Rubber Cushion (Option) w Mounting Bolt q Mounting Collar 30 CQ-FX85LEN ¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries. ¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness. (a Page 34) 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. E N G L I S H 16 Lock Lever (C) Power Connector y Mounting Tabs Mounting Bolt w 2 3 4 Make sure that the lock lever (C) is flush with the mounting collar (not projecting outward). Lock Lever Secure the rear of the unit. After fixing Mounting Bolt w and Power Connector y, fix the rear of the unit to the car body by either method (a) or (b) shown at left. Insert Trim Plate i. After installation reconnect the negative (­) battery terminal. CQ-FX85LEN 31 Installation (continued) E N G L I S H 17 To Remove the Unit q Remove the removable face plate. (b) Push the face plate to either the right or left, then pull it out toward you. PTY PWR Open q Open OPEN Contact w Push MONO/LOC e Pull out w Remove the trim plate i with a screwdriver. iTrim Plate Screwdriver 1 2 e Pull out the unit while pushing down the lock lever with a screwdriver. Lock Lever Lock Lever r Remove the unit pulling with both hands. Cautions: ¡Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. ¡If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth. [. . . ] Grounding wire is not correctly connected. Step Turn your car's ignition switch to ACC or ON. Connect the battery cable to the terminal that is always live. Connect the accessory cable to your car's ACC source. [. . . ]