User manual PANASONIC CQ-VX2200

[. . . ] R INTEGRATED CD/CASSETTE RECEIVER WITH DSP Human Equalizer REMOTE OPEN CQ-VX2200 REVERSE SEL SKIP SPACE POSI ST EQ B NR PWR SOURCE S·A S·ANALYZER FM DISC DISC D·M AM4 5DISC REP R CQ-VX2200W Operating Instructions SCAN TPS AUTO·P MUTE MTL LOC TUNE TRACK INTEGRATED CD/CASSETTE RECEIVER WITH DSP DISPLAY CLOCK RANDOM SCAN REPEAT DSP SPACE VOL DISP 1 MTL 2 B NR 3 4 TPS 5 SKIP 6 REPEAT SPACE ¡Please read these instructions carefully before using this product and keep this manual for future reference. E N G L I S H Safety Information WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Contents Page Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Use This Product Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 24 1 Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If the bulb also turns off and on, that outlet is the car power lead. If your car is not wired for an audio unit : Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function. ) CQ-VX2200W 33 E N G L I S H 25 Installation Guide(continued) Connect All Leads Now that you have identified all the wires in the car, you're ready to begin connecting them to the stereo unit wires. The connection diagram (a Page 36 to 38) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Use electrical tape to cover all exposed wires. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis. See the wiring diagram below for the proper hookups. Follow the diagram carefully to avoid damaging the speakers and the stereo unit. The speaker used must be able to handle more than 41 W of audio power. If using an optional audio power, the speakers should be able to handle the maximum amplifier output power. Speakers with low input ratings can be damaged. Speaker impedance should measure 4 - 8 , which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage. [. . . ] a Open the panel and press [u] (CD EJECT) button. CD ­ E1 ­ CD ­ E2 ­ CD ­ E3 ­ PLS EJECT Cassette Tape Display Cause / Step No operation by some cause. a Open the panel and press [u] (CST EJECT) button. PLS EJECT CD Changer Display Cause / Step Disc is dirty, or is upside down. a Select the next available compact disc. a Select the next available compact disc. [. . . ]