User manual PANASONIC CS-W24BD2P

[. . . ] Air Conditioner OPERATING INSTRUCTIONS ­­ INDOOR UNIT ­­ Model ­­­­­­­­­­­­­­­­ OUTDOOR UNIT ­­­­­­­­­­­­­­­­ Heat Pump Model (220~240V, 50Hz, 1 Phase) Cooling Model (220~240V, 50Hz, 1 Phase) CS-W24BD2P CS-W28BD2P CS-W34BD2P CS-W43BD2P CS-W50BD2P CU-W24BBP5 CU-W28BBP5 (380~415V, 50Hz, 3 Phase) CU-V24BBP5 CU-V28BBP5 (380~415V, 50Hz, 3 Phase) CU-W28BBP8 CU-W34BBP8 CU-W43BBP8 CU-W50BBP8 CU-V24BBP8 CU-V28BBP8 CU-V34BBP8 CU-V43BBP8 CU-V50BBP8 Before using your air-conditioner, please read this operating instructions carefully and keep it for future reference. ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 001 PORTUGUÊS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 016 DEUTSCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 031 FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (You will need to reset the timer if the power supply for the unit stops for an hour or more due to power outage or disconnected from the power supply. However, depending on the ambient temperature, there may be cases where the setting is cleared within an hour. ) TIMER SELECT SET FAN OPESPEED RATION TEMP UP DOWN FILTER RESET 1 Press A to start the operation. Press once more to stop the operation. TEST RUN CLOCK CANCEL CHECK A/C No. 2 Press B to select the desired operation mode. The display changes in this order. For Heat Pump models OPERATION OPERATION OPERATION OPERATION AUTO OPERATION HEAT FAN COOL DRY FAN COOL For Cooling models OPERATION OPERATION OPERATION OPERATION AUTO DRY AUTO operation Indoor unit will automatically detect the temperature differences between the remote control set temperature and the inlet air temperature, and automatically switches operation between HEAT, FAN and COOL mode to maintain a constant room temperature. (For Cooling models, the operation mode switches between COOL and FAN to maintain a constant room temperature. ) DRY operation Indoor unit will automatically switch to cooling operation with a low fan speed. (The outdoor unit will be cut-off if the room temperature is less than 21°C or the remote control set temperature is higher than the room temperature. ) 3 4 Press C to select the setting temperature (16°C ­ 31°C). UP DOWN Press to increase temperature by 1°C. Press to decrease temperature by 1°C. Press D to select the fan speed. The display changes in this order. FAN SPEED FAN SPEED FAN SPEED AUTO FAN SPEED MED HI LO AUTO fan speed Indoor unit will detect the temperature differences between the remote control set temperature and the inlet air temperature, and switches the fan speed accordingly. The larger the difference between the two temperatures, the greater will be the fan speed. (If the operation mode is set to FAN, the fan speed will be fixed at MED regardless of the temperature difference. ) ­7­ 4-3 How to operate (with timer operation) * Set the clock and other operation details (refer to page 7 for operation setting details) before setting the timer. Setting the current time Example: setting the time to 10:36 a. m. AIR SWING TIMER LOCAL OPEFAN SPEED RATION TEMP MED 1 2 3 Press A to activate the setting time. (Example) TIMER (Time display will flash. ) COOL OFF / ON TIMER SELECT SET FAN OPESPEED RATION TEMP UP DOWN FILTER RESET TEST RUN CLOCK CANCEL CHECK A/C No. Press B to set the desired time. To set an earlier time, press the button. The setting changes more rapidly if the buttons are pressed continuously. Press A once more to complete the settings. (Example) TIMER (The time display will stop flashing. ) Setting timer operation Timer operation can be used to start and stop the indoor unit automatically. To set the OFF timer To set the ON timer 1 Press C to activate the OFF time setting. The unit contains a crank case heater to protect the compressor. When the unit is not in use for a long period of time, turn off the circuit breaker (the heater consumes 25 to 40 watts of electricity per hour). · Remove dust from the outdoor unit. · Clean off the rust on the outdoor unit to prevent it from spreading. Before starting the air conditioner for the first time in the season · Check that the inlet and outlet vents of both the indoor and outdoor units are not blocked. · Check that the ground wire is connected and is in good condition. · Check that the air filter has been cleaned. · Turn on the circuit breaker about 12 hours before operating the air conditioner. Operating the air conditioner immediately after turning on the circuit breaker may cause damage to the unit. Do not cut off the circuit breaker during the season. 6. PROPER USE Avoid direct sunlight while cooling Close the windows' curtains or blinds. Do not use other heating equipments in the same room while operating the unit Using heating equipment will reduce the unit's cooling efficiency. Do not block the airflow Do not place anything near to the inlet and outlet vents. [. . . ] If operating the indoor unit for a long period of time, use dry operation to lower the humidity. · This is a normal operation as there is a auto restart operation function. The operation will resume based on the previous settings. During heating operation (Heat Pump type only) Airflow does not start immediately after operation is started. ("PRE HEAT" appears in the remote control display. ) Operation stops occasionally. [. . . ]