User manual PANASONIC CU-4E23JBE

[. . . ] 6 Indoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 OPERATION I DRY · COOL · FAN Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 I POWERFUL Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 I Adjusting the Air Flow Direction Adjusting the horizontal blade (flap) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When the unit receives a signal, you will hear a short beep. · In the case of multi system operation, there are times when the unit does not activate with this button. ) 4 Names of Parts Outdoor unit Air inlet (Back and side) Refrigerant piping and inter-unit cable Air outlet Drain hose Earth terminal It is inside of this part. Appearance of the outdoor unit may differ with some models. Remote controller <CS-MK90/120> Transmitter sends signals to the indoor unit. Display Open the cover. displays the current settings. (In this illustration, each section is shown with all its displays ON for the purpose of explanation. Some models may not show all its indications. ) OFF/ON ON/OFF button Press it once to start operation. To stop it, press it once again. ON TEMP TEMPERATURE/TIME adjustment buttons change the temperature or time setting. C AMPM TIME OFF-TIMER CLOCK ON-TIMER CANCEL CLOCK button (See page 7 "Preparation Before Operation - Setting the Clock) OFF TIMER button ON TIMER button (See page 10 "Timer Operation") AMPM FAN SPEED MODE TIMER CANCEL button cancels the timer setting. MODE selector button selects the operation mode. : DRY : COOL : FAN SWING POWERFUL FAN setting button selects the air flow rate setting. SWING button (See page 9 "Adjusting the Air Flow Direction") POWERFULL button (See page 8 "POWERFUL Operation") ARC417A24 <CS-MK180> MODE SWING POWERFUL SWING button (See page 9 "Adjusting the Air Flow Direction") ARC417A25 5 Preparation Before Operation Remote controller Setting the batteries Position and correctly!Address switch Operating the remote controller · To use the remote controller, aim the transmitter at the indoor · · unit. If there is anything to block signals between the unit and the remote controller, such as a curtain, the unit will not operate. The maximum distance for communication is about 7 m. 2 Receiver 3 1 1 2 3· Press with a finger and slide the back cover to take it off. Set the back cover as before. This will cause the figures on the display to flash. Set the clock at this point. To fix the remote controller holder on the wall 1 2 3 Choose a place from where the signals reach the unit. Fix the holder to a wall, a pillar, etc. Moreover, for precedence-room settings, please consult your dealer or service shop. I To change the temperature setting: DRY or FAN mode Press The temperature setting is not variable. COOL mode to raise the temperature and press to lower the temperature. Set to the temperature you like. C POWERFUL Operation POWERFUL operation quickly maximizes the cooling effect in any operation mode. You can get the maximum capacity with a touch of a button. · Pressing the (POWERFUL) button during operation starts POWERFUL operation. · POWERFUL operation ends in 20 minutes. Then the system automatically operates again with the settings which were used before POWERFUL operation. Press FAN SPEED . COOL or FAN mode Press . DRY mode The air flow rate setting is not variable. I To cancel POWERFUL operation: " to Five levels of air flow rate setting from " " " plus " " are available. Press POWERFUL . Display Notes on POWERFUL operation · In COOL mode · At smaller air flow rates, the cooling or heating effect is also smaller. · · 8 To maximize the cooling and heating effect, the capacity of outdoor unit must be increased and the air flow rate be fixed to the maximum setting. The temperature and air flow settings are not variable. In DRY mode The temperature setting is lowered by 3°C and the air flow rate is slightly increased. In FAN mode The air flow rate is fixed to the maximum setting. Display I To change the air flow rate setting: Display 1 POWERFUL Adjusting the Air Flow Direction You can adjust the air flow direction to increase your comfort. Adjusting the louvre <CS-MK90/120> Adjusting the horizontal blade (flap) Press SWING . " appears or · Every time the button is pressed, " disappears. . . . . . . . The flap automatically swings up and down. . . . . . . . To stop the flap at an angle you like, press No display SWING . Hold the knob and move the louvre. [. . . ] I For system protection, the air conditioner may stop operating on a sudden large voltage fluctuation. It automatically resumes operation in about 3 minutes. Mists come out of the indoor unit. The indoor unit gives out odour. The outdoor fan rotates while the air conditioner is not in operation. The operation stopped denly. (OPERATION lamp is on) sud- 13 Trouble Shooting Check again Please check again before calling a repair person. Case The air conditioner does not operate. [. . . ]