User manual PANASONIC CZ01ESM11P

[. . . ] PACKAGED AIR CONDITIONER CENTRAL REMOTE CONTROLLER Model No. CZ-01ESM11P En. Thank you for purchasing Panasonic's central remote controller. For proper usage, read this instruction manual carefully before using this unit. This manual will help you with anything you can not understand or should anything go wrong with the unit during use. [. . . ] Power reminder stops. w Stop v --- Operation Stop v --- Programmed to stop at 10:00 Remote controller Only stopping possible by the remote controller. Centralized AM SET1 ON OFF PM Centralized Operation controlled by timer w Timer stops. w SET2 ON OFF Programmed to operate at 8:45 Remote controller Stop v --- Operation v Stop v --- Programmed to stop at 7:00 Operation/stop is possible by the remote controller during the hours programmed for timer operation. Individual SET1 ON OFF PM Centralized AM Operation starts without fail at the timer-programmed time. w SET2 ON OFF PM Operation v Programmed to operate at 9:00 Stop v --- Operation v Remote controller Operation/stop is possible by the remote controller at any time regardless of the hours programmed by the timer. Stops temporarily at the timer-programmed stop time. w Centralized Timer stops. w Stop v --- Programmed to stop at 5:00 --- Operation v Stop v --- Programmed to stop at 10:00 Remote controller Operation/stop is possible by the remote controller at any time regardless of the hours programmed by the timer. Timer operation possible by remote controller SET1 ON OFF PM Centralized Timer operation possible by remote controller at preset times. w AM Stops for a time at timer-programmed time. w PM v v Remote controller Operation/stop is possible by the remote controller during the hours programmed for timer operation. --------- -----------------------------------------Timer operation possible by remote controller at preset times. w Centralized Timer stops. Power reminder stops. w ------ Programmed to operate at 5:20 --- Operation v Stop v --- Programmed to stop at 10:00 Remote controller Operation/stop is possible by the remote controller during the hours programmed for timer operation. Air conditioner now operating. Command by central remote controller Command by remote controller 26 -------- SET2 ON OFF PM 8:30 --- Operation Stop --- Programmed to stop at 5:00 ---- ENGLISH SETTING OPERATION MODE (Fig. 5) The Zone consists of the following two cases. A. Zone without display " " List of setting operation A: Zones not displayed Display M Setting Contents of setting M To be set by zone M The group with master remote controller setting exists in this zone. Setting the master remote controller enables cool/ heat selection. Operations other than cool/heat operations can also be set for some operations. For further details, see the list on the right. 1 M To be set by zone To be set by zone M To be set by zone M 1 M To be set by zone To be set by zone Select this display if you don't wish to set by zone. 1 B. Zone with display " " M No group with master remote controller setting exists in this zone. The cool/heat selection is not available because the master remote controller has not been set. Some operations other than cool/heat operations can be set. For further details, see the list in the right. Display ---- B: Zones displayed Setting M Contents of setting 2 To be set by zone M See page 31 if the display " " is flashing. M 1 Press the OPERATION MODE SELECTOR BUTTON. Each time you press this button, the display rotates as shown on the right list. M M M NOTES During cool/heat operation, this central remote controller enables FAN operation for each zone even without setting the master remote controller. Meanwhile, ventilation, ventilation/cleaning, etc. are connected with this unit in the zone. See the operation manual provided with the each unit. When the indoor unit is in heat operation, change the setting to FAN operation through the central remote controller; then, you can switch the fan speed to the extremely low fan speed. Warm air may blow if any other indoor unit belonging to the same system is in heat operation. The indoor fan stops during defrost/hot start. DRY cannot be set from the central remote controller. 1 M To be set by zone 1 M ---- Select this display if you don't wish to set by zone. Note) In the above list, " " refers to the acceptable setting, while " " refers to the not acceptable setting. [. . . ] The delay is due to signal exchange. 31 When installing the equipment, mark the zone No. of each group and installation location in the below table. Setting group No. (Setting is not possible unless power is activated to both the central remote controller and indoor unit. ) Operated by simplified remote controller 1. Activate power to both the central remote controller and indoor unit. Press the BS6 BUTTON (field set) on the PC board. [. . . ]