User manual PANASONIC CZRWSU2N

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PANASONIC CZRWSU2N. We hope that this PANASONIC CZRWSU2N user guide will be useful to you.

Lastmanuals help download the user guide PANASONIC CZRWSU2N.


Mode d'emploi PANASONIC CZRWSU2N
Download
Manual abstract: user guide PANASONIC CZRWSU2N

Detailed instructions for use are in the User's Guide.

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ρ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Remote control sensor Detects the temperature at the remote controller when detection has been switched to the remote controller by the sensor button. Filter button CZ-RWSC3 Press to turn off the filter lamp on the receiver. Pressing this button starts and stops the fan. When the air conditioner is started or stopped, the fan starts or stops at the same time. ( appears on the display of the remote controller when the fan is operating. Sensor button Used this to activate the temperature sensor on the remote controller instead of the one on the indoor unit. The temperature sensor on the indoor unit is selected before is shown on the shipment. From this page, the names of remote controller’s buttons will be indicated with the above illustrations. Indd 4 2015/02/17 15:01:45 Receiver CZ-RWSU2N CZ-RWSD2 2 CZ-RWSC3 ADDRESS 1 ADDRESS 2 ADDRESS 3 REM SUB/MAIN 1 3 4 5 1 2 CZ-RWSL2N 3 4 5 1 2 1234 Display 3 4 5 6 Front side CZ-RWST3N 2 Rear side 9 7 8 Operation Panel 3 4 OPERATION TIMER STANDBY 3 2 3 4 5 4 5 1 1 2 5 For wall mounted type indoor unit (CZ-RWSK2) 1. Receiver Receives the signal sent from the remote controller. Emergency operation button Indicator lamps When an error occurs, one of the lamps flashes. STANDBY lamp • The lamp in the HEAT mode lights up at the following times: during the startup, during the thermostat operation, and during the defrosting. FILTER lamp This lamp is for notifying you when the filter needs to be cleaned. Address switch Used to set the remote controller addresses. Note • If non-cooling/heating free type is being used, it will beep twice and the operating lamp will light up on the display; if the timer and standby lamps blink alternately, a conflict between the heating and cooling exists, so the unit cannot operate in the desired mode. (On models that do not have an Auto function, even if Auto is selected, it works in the same way. ) • When the local operation is disabled by centralized control or similar cause, and if the Start/Stop , Mode or Temperature setting button is pressed, the unit will beep five times and the change will not be made. Appears when a fan available in the market is installed and is operating. Timer program indication : The indoor unit starts operation at the programmed time. : The indoor unit stops operation at the programmed time. Indicates the remote controller addresses are set. The indoor unit filter needs to be cleaned. [. . . ] ) If you cannot turn the air conditioner off in the normal way Disconnect the power to the indoor unit and contact the distributor where the product was purchased. <Auto operation> Only when identical refrigerant system inside all the indoor units or cooling/heating free-type are under control as one group. It heats or cools automatically via the differences between the set temperature and the room temperature. <Dry operation> • • • • • Depending on the indoor unit used, the remote controller may have a [Dry] indicator on its display even though the unit does not have the Dry function. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC CZRWSU2N

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC CZRWSU2N will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag