User manual PANASONIC DMW-FL28E

[. . . ] DMW-FL28E. book 1 ページ ２００７年３月６日　火曜日　午前１０時２１分 Auto Flash Operating Instructions Bedienungsanleitung Mode d’emploi Instrucciones de funcionamiento Istruzioni per l’uso Model. No DMW-FL28E Before use, please read these instructions completely. VQT9889 DMW-FL28E. book 2 ページ ２００７年３月６日　火曜日　午前１０時２１分 Contents Parts Identification. . 8 Selecting the shutter speed and aperture (when using DMC-LC5) . . 9 Selecting the shutter speed for use with Analog Cameras . [. . . ] • Auto-effective distance and ISO sensitivity are dependent on automatic aperture control D F5. 6 F4 F2. 8 0. 5~5m 0. 7~7m 1. 0~10m 0. 5~3. 5m 0. 5~5m 0. 7~7m M GN    AUTO F N W AUTO(W) 28 14 7 20 10 5 16 11 8 5. 6 4 2. 8 ∼5m (∼3. 5m) ∼7m (∼5m) ∼10m (∼7m) ISO100 AUTO 0. 7m∼(W 0. 5m∼) GN F＝ m AUTO CHECK PL SLAVE MANUAL AUTO AUTO TEST OFF E ISO25 F2. 8 F2 F1. 4 ISO50 ISO100 ISO200 ISO400 ISO800 F11 F16 a F4 F8 F5. 6 F11 b F8 F2. 8 F4 F5. 6 F8 F2 F2. 8 F4 F5. 6 c LOOK M GN    AUTO F N W AUTO(W) ∼5m (∼3. 5m) ∼7m (∼5m) ∼10m (∼7m) 1 • Even if a different ISO sensitivity is set, the auto-effective distance is constant, while the F number should vary. A F number fitting B When not fitting the wide panel C When fitting the wide panel D ISO sensitivity E F number on the camera a b c 28 14 7 20 10 5 16 11 8 5. 6 4 2. 8 ISO100 AUTO 0. 7m∼(W 0. 5m∼) GN F＝ m AUTO CHECK PL SLAVE MANUAL AUTO AUTO TEST OFF 1 2 3 4 5 6 7 11 DMW-FL28E. book 12 ページ ２００７年３月６日　火曜日　午前１０時２１分 Auto check indicator If the auto check indicator lights at the instant of pressing the test flash button, it indicates that the auto circuit is operating. If the auto check indicator does not light, the subject is beyond the auto-effective distance. Adjust either the auto F number with the rotary switch B 2 or the distance to the subject. M GN    AUTO F N W AUTO(W) 2 28 14 7 20 10 5 16 11 8 5. 6 4 2. 8 ∼5m (∼3. 5m) ∼7m (∼5m) ∼10m (∼7m) ISO100 AUTO 0. 7m∼(W 0. 5m∼) GN F＝ m AUTO CHECK SLAVE MANUAL AUTO Selecting the aperture for use with Analog Cameras (for close-up AUTO recording (AUTO )) 1. Fit the wide panel onto the flashtube and set the rotary switch A 1 to [AUTO ] as illustrated. Set the F number on the camera in accordance with ISO sensitivity in use. As long as the subjects are within the auto-effective distance, the flash automatically adjusts the amount of light. Determine the positions of the flash at the camera side and DMW-FL28 for slave. Direct the slave photoreceptor of the slave unit so that it can receive either direct or reflected light from the flash at the camera side. Turn on both the flash at the camera side and the slave (this flash). Set the rotary switch A to [SLAVE] on the unit. Check that the flash indicator on both units light. When pressing the test flash button on the flash at the camera side, it lights. The flash triggers the slave (this unit) causing it to flash almost simultaneously. If the slave (this unit) does not light, check the facing direction of the slave and the operating distance. DMW-FL28 (this unit) allows the Guide Number (GN) to be switched. In accordance with the recording condition, set the rotary switch B to GN 28, GN 14 or GN 7. • Use the flash at the camera side in the manual mode. Use the slave (this unit) in the slave mode. DMW-FL28 (this unit) may slaveflash in response to the AF auxiliary light or preparatory lighting. [. . . ] In this case, use the flash light in the manual mode. For cameras with a lens shutter (Example) Recording in backlight condition When using a 35-mm camera fitted with a 35-mm lens and a ISO sensitivity 100, normal exposure with available light indicated being F11, 1/125 sec (= F8, 1/250 sec) and the recording distance being 3 m: 1. F number for using a flash light is GN/distance(m)=28/3 = about 8 Set F8 on the camera. The shutter speed when the F number with available light is F8 is 1/250 sec. [. . . ]