User manual PANASONIC FV08VKSL2

[. . . ] Ventilating Fan INSTALLATION INSTRUCTIONS Model No. FV-08VKML2 FV-08VKSL2 FV-08VKML2 FV-08VKSL2 READ AND SAVE THESE INSTRUCTIONS. Thank you very much for having purchased our Ventilating Fan . Please read these instructions carefully before attempting to install, operate or service the Panasonic Ventilating Fan. Failure to comply with instructions could result in personal injury and/or property damage. Please retain this booklet for future reference. Table of Contents Please Read Prior To Installing This Fan Unpacking Supplied Accessories Description Dimensions Wiring Diagram Switch Indication Operation Specifications General Safety Information Installation I (Joist Mounting- I ) Installation II (Joist Mounting- II ) Installation III ( I -Joist Mounting) Installation I Installation Installation (Suspended Between Joist Mounting) (Wooden Header) I (In Existing Construction) 2 3 3 3 4 5 5 6 6 7 8-10 11-12 12 13 14 14 15-16 16 16 Maintenance Practical Guide To Installation Product Service PLEASE READ PRIOR TO INSTALLING THIS FAN The WhisperGreen TM line of ventilating fans employs state of the art technology providing a number of unique features that lead to improved indoor air quality. These features need to be fully understood prior to installation to fully realize the benefits the fans offer. [. . . ] Refer to switch indication on page 5 (FV-08VKML2) (Fig. 6-1) Ceiling Sensor unit Gloves Fig. 6-1 11. Insert the sensor unit into the housing of the grille and insert other mounting spring into the slot as shown and mount grille to fan body (FV-08VKML2) (Fig. 6-2, Fig. 6-3) Grille Lighting unit Ceiling Grille Sensor unit Gloves CAUTION: Mount grille carefully so that lead wire of sensor unit is not pinched. Ceiling Fig. 6-2 Mounting spring 12. Insert mounting springs into the slots as shown and mount grille to fan body. (FV-08VKSL2) (Fig. 7) Grille Gloves Fig. 6-3 Slot Lighting unit Mounting spring Ceiling Gloves Grille Fig. 7 10 INSTALLATION (When spacing the fan body flange below the drywall or resilient channel) plug connector Machine screw Receptacle (JOIST MOUNTING- ) 1. Remove the machine screw by using screw driver, disconnect plug connector from receptacle and remove adaptor from fan body before installation, (Fig. 8) 2. Insert the suspension bracket into the adaptor and secure it to joists by using long screws (ST4. 2X20) (Fig. 9) Keep the distance B (1/ 2 inch, 12. 7mm or 5/8 inch, 15. 9mm) for the thickness of ceiling board. If spacing A between joists is 21 1/4 to 23 1/ 2 inches (540 to 597mm), connect suspension bracket II and III (C4 mark to C4 mark) according to page. 8 Select the suspension bracket according to spacing A as shown below: Spacing A between Joists inches (mm) Suspension bracket 13 1/4~ 15 1/2 (336~394) Suspension bracket I 16 1/ 2 ~18 3/4 (419~480) Suspension bracket III 21 1/4~ 23 1/ 2 (540~597) Suspension bracket II III (FV-08VKML2) Suspension Screw driver Fan body Adaptor bracket I plug connector Receptacle Gloves Gloves (FV-08VKSL2) Fig. 8 2 Long screws (ST4. 2X20) Joists 2 Long screws (ST4. 2X20) Gloves Suspension bracket Adaptor 13 1/4~15 1/2 (336~394) 16 1/2~18 3/4 (419~480) 21 1/4~23 1/2 (540~597) 4. Insert the suspension bracket into fan body (refering to step 1 of installation I, page 8) Inches (mm) 5. (Fig. 10) Joist 1/ 2 (12. 7) 5/8 (15. 9) Fig. 9 Circular duct Conduit Junction box cover IMPORTANT: Make sure that adaptor claws are properly inserted into fan body slots. Fan body Gloves Slots Adaptor claws Fig. 10 11 INSTALLATION (JOIST MOUNTING- ) CONTINUED 6. Secure the fan body to adaptor by using machine screw and plug connector to receptacle (Fig. 11) (FV-08VKML2) (FV-08VKSL2) Screw driver Machine screw Plug connector Receptacle Fig. 11 7. Secure the suspension bracket to joists by using long screws (ST4. 2X20) and secure it to fan body by using screw II (ST4. 2X12) in vertical direction (Fig. 12) Screw II (ST4. 2X12) 8. Follow steps 7 to 12 of Installation I (page 10) to complete the installation work. 2 Long screws (ST4. 2X20) 2 Long screws (ST4. 2X20) Fig. 12 INSTALLATION ( -JOIST MOUNTING) 4 kinds of -joist inches (mm) 9/16 (14. 3) 11/16 (17. 5) 31/32 (24. 6) 1 17/32 (38. 9) C3 hole mark C1 Suspension bracket III Screw II (ST4. 2X12) C2 C3 C4 Fig. 13 C4 C2 C1 Suspension bracket III The suspension bracket III can comply with different kind of I-joists. Before installation, secure the lighting unit to fan body (refering to Fig. 5 of page 10). Connect the suspension bracket III to fan body. (Fig. 13) (Select the hole by checking -joist size and fix the screw to the frame hole. ) 3. Follow steps 4 to 12 of installation I (page 9, page 10) to complete the installation work. 12 I-joist 4 Long screws (ST4. 2X20) Fig. 14 INSTALLATION (SUSPENDED BETWEEN JOIST MOUNTING) Suspension bracket I 16 inches and 19. 2 inches horizontal joist 1. Before installation, secure the lighting unit to fan body (refering to Fig. 5 of page 10). Insert the suspension bracket into bracket cover of adaptor side and the back of the fan body. (Fig. 15-1, 15-2) (select the suspension bracket according to spacing A as shown below. ) 16 inches and 19. 2 inches horizontal joist Suspension bracket II Suspension bracket III Suspension bracket III Fig. 15-1 19. 2 inches vertical joist Suspension bracket I 3. Make sure the fan body is level and square (perpendicular) with the joists. [. . . ] The grille should be dry after cleaning. Remove dust and dirt from fan body using a vacuum cleaner. Using a cloth dampened with kitchen detergent, remove any dirt from fan body. (Fig. 25) Vacuum cleaner Fig. 24 6. [. . . ]