User manual PANASONIC HFS1442AE

[. . . ] ‰¥ Four ThirdsTM and Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. ≥ G MICRO SYSTEM is an interchangeable lens type digital camera system of LUMIX based on a Micro Four Thirds System standard. ‰¥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned. Book 3 ページ ２０１２年１２月２１日　金曜日　午後６時２８分 ENGLISH -If you see this symbol- Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. [. . . ] ) • Do not press the lens release button C when you attach a lens. €¢ Do not try to attach the lens when holding it at an angle to the camera body as the lens mount may get scratched. Book 6 ページ ２０１２年１２月２１日　金曜日　午後６時２８分 ∫Detaching the Lens ≥ Check that the camera is turned off. ˆ« Attaching the Lens Hood (Supplied Accessory) Hold the lens hood with your fingers placed as shown in the picture. €¢ Do not hold the lens hood in a way that twists or bends it. While pressing on the lens release button D, rotate the lens toward the arrow until it stops and then remove. €¢ Attach the lens rear cap so that the lens contact point does not get scratched. €¢ Attach the body cap to the camera so no dirt or dust will get inside the main unit. ˆ«Attaching and Detaching the Lens Cap Pinch the lens cap as shown in the figure to attach or detach. ‰¥ Be careful not to lose the lens cap. 1 Align the fitting mark E on the short side of the lens hood with the mark on the tip of the lens. 2 Turn the lens hood in the direction of the arrow until it stops, and align the stop mark F on the long side of the lens hood with the mark on the tip of the lens. Fm 7 ページ ２０１３年１月２１日　月曜日　午前１０時１９分 ∫ Temporarily Storing the Lens Hood 1 Turn the lens hood in the direction of the arrow to detach it. ˆ« Attaching Filters ≥ Vignetting may occur if using 2 or more MC protectors (optional: DMW-LMC46), PL filters (optional: DMW-LPL46) or ND filters (optional: DMW-LND46), or if using thick protectors and/or filters. ‰¥ The filter may become impossible to remove if excessively tightened, so please refrain from tightening it too strongly. ‰¥ It is possible to attach the lens cap with the filter already attached. ‰¥ You cannot attach a conversion lens or adaptor to this lens. A filter may be used, but attaching any other element may cause damage to the lens. 2 Reverse the lens hood and then attach it in the same way as shown previously. Note ≥ When taking pictures with the flash with the lens hood attached, the lower portion of the screen may turn dark (vignetting effect) and the control of the flash may be disabled because the photo flash may be obscured by the lens hood. ‰¥ When using the AF assist lamp in the dark, detach the lens hood. Book 8 ページ ２０１２年１２月２１日　金曜日　午後６時２８分 Names and Functions of Components Note ≥ When flash recording with a close subject, the light of the flash will be blocked by the lens and part of the picture may be dark. [. . . ] When this lens is attached to digital camera, stabiliser function cannot be turned off or stabiliser function does not work. ‰¥ The Optical Image Stabiliser function of this lens only works correctly with supported cameras. > When older Panasonic digital cameras (DMC-GF1, DMC-GH1, DMC-G1) are used, [Stabilizer] in the [Rec] mode menu cannot be set to [OFF]. It is recommended to update the firmware of the digital camera at the following website. [. . . ]