User manual PANASONIC KX-DT333 QUICK REFERENCE GUIDE

[. . . ] Quick Reference Guide <KX-DT346> Digital Proprietary Telephone Model No. KX-DT333/KX-DT343/KX-DT346 Thank you for purchasing a Digital Proprietary Telephone (DPT). Please read this manual carefully before using this product and save this manual for future use. For more details, please refer to the manuals of the PBX. [. . . ] Locking the Handset Hook Pull down the handset hook until it locks to prevent the handset from falling off the handset cradle when the unit is mounted to a wall or set at a high angle. To temporarily place the handset down during a conversation, hook it over the top edge of the unit as shown. 12 Document Version 2009-03 Connection Connection <Back view> Connect to: a digital proprietary telephone -- Digital XDP connection a single line telephone -- XDP or parallel connection The telephone line cord (included) Connect to a PBX. Clamp Headset Recommended: KX-TCA86, KX-TCA91, KX-TCA92 Do not use a KX-T7090 headset. Consult your dealer for more details about XDP and Digital XDP. CAUTION: When connecting a headset When connecting cords Ensure that the headset cord is wound around the hook to prevent damage to the connector. Ensure the cords are inserted in the grooves, and are clamped to prevent damage to the connectors. Document Version 2009-03 13 Installing KX-DT301/KX-NT303 Installing KX-DT301/KX-NT303 CAUTION: To prevent damage to the telephone, be sure to unplug the extension line before you set up or remove the KX-DT301 (USB Module) or the KX-NT303 (Add-on 12 Key Module). Connect the KX-NT303 first when installing both the KX-DT301 and the KX-NT303. KX-NT303 The Add-on 12 Key Module allows 12 additional flexible buttons to be added to this unit. These buttons are used to seize a CO line, make a call using One-touch Dialing, or perform a feature that has been assigned to the key. Attach the KX-NT303 to your unit with the screws (included with KX-NT303). 1. Plug the flat cable into the connector (A), then bend the cable slightly as shown (B). 4. Close the cover. 14 Document Version 2009-03 Installing KX-DT301/KX-NT303 KX-DT301 The USB Module can be connected between the DPT and the personal computer through USB interface to implement personal CTI (Computer Telephony Integration). Plug the flat cable into the connector as shown. 3. Connect the USB cable to the USB port. Connect to a PC Ensure that the USB cable goes through the cable guide. Please use a USB cable shorter than 3 m (9 ft 10 in). Document Version 2009-03 15 Installing KX-DT301/KX-NT303 5. Insert the protrusions on the KX-DT301 into the 2 holes in the unit. Attach the KX-DT301 to your unit with the screws (included with KX-DT301). 7. Refer to Installation Manual on the CD-ROM included with KXDT301. 16 Document Version 2009-03 Wall Mounting Wall Mounting 1. Remove the wall mounting adaptor from the unit as shown. Set the operation board to level 1, then connect and secure the telephone line cords. The cords can also be run from the top of the unit (page 13). 3. Attach the wall mounting adaptor as shown. Make sure the cords are not pinched by the wall mounting adaptor. These noise sources can interfere with the performance of the unit. It also should not be placed in rooms where the temperature is less than 5 C (41 F) or greater than 40 C (104 F). Allow 10 cm (3-15/16 in) clearance around the unit for proper ventilation. Placement 1) Do not place heavy objects on top of this unit. [. . . ] 13. Do not use a telephone in the vicinity of a gas leak to report the leak. SAVE THESE INSTRUCTIONS 20 Document Version 2009-03 Important Information FCC and Other Information F. C. C. REQUIREMENTS AND RELEVANT INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]