User manual PANASONIC KX-T7636NE

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co. , Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www. doc. panasonic. de Contact: Panasonic Services Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, F. R. [. . . ] Press {ih}. Note: L When the night mode is turned on, "[N]" is displayed. Setting the ring delay for night mode This setting allows the handset to ring during night mode if the caller waits long enough. After the selected amount of time passes, the handset will ring, useful when someone urgently needs to speak with you. If you select "No Ringing", the handset will not ring during night mode. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Start/End", then press {>}. 6 Enter the desired hour and minute you wish to start this feature by selecting 2 digits for each. L If you use 12-hour time entry, select "AM" or "PM" by pressing {*} repeatedly before entering the time. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Ring Delay", then press {>}. 6 Select the desired setting, then press {>}. 7 Enter the desired hour and minute you wish to end this feature by selecting 2 digits for each. 7 Press {ih}. 19 TCD200FX(e-e). book Page 20 Monday, February 7, 2005 1:19 PM Handset Settings Selecting categories to bypass night mode 4 Select "Standby Display", then press {>}. 1 Press {j/OK}. Includes confirmation tones and error tones. Turning auto talk on/off When this feature is turned on, you can answer calls simply by lifting the handset off the base unit. You do not need to press {C}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Other Options", then press {>}. 3 Select "Call Options", then press {>}. 4 Select "Auto Talk", then press {>}. 5 Select "On" or "Off", then press {>}. 6 Press {ih}. 4 Select "Keytones", then press {>}. 5 Select "On" or "Off", then press {>}. 6 Press {ih}. 21 TCD200FX(e-e). book Page 22 Monday, February 7, 2005 1:19 PM Handset Settings Note: L If keytones are turned off, error tones will not sound when you enter the wrong PIN or when memory is full. Resetting the handset to its default settings 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Other Options", then press {>}. 4 Select "Reset Handset", then press {>}. 5 Enter "0000" (default handset PIN). L If you changed the PIN, enter it (page 21). 6 Select "Yes", then press {>}. 7 Press {ih}. Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 17 ­ Redial list ­ Voice enhancer ­ Category names ­ Category ringtones L The following items will be retained: ­ Phonebook entries (category names and ringtones will be reset to their default settings. ) ­ Date and time 22 TCD200FX(e-e). book Page 23 Monday, February 7, 2005 1:19 PM Base Unit Settings Guide to base unit settings For your reference, a chart of all items which can be customised for the base unit is printed below. L When customising the base unit, the current item or setting is indicated by >. [. . . ] Connect the AC adaptor, turn on the handset and try again. Start again. While storing an entry in the phonebook or assigning a one touch dial, the handset starts to ring. Pressing {R} does not L The redialled number was more than 24 digits long. The handset beeps intermittently L Fully charge the batteries (page 8). [. . . ]