User manual PANASONIC KX-TCD200FX

[. . . ] TCD200FX(e-e). book Page 1 Monday, February 7, 2005 1:19 PM Operating Instructions Digital Cordless Phone Model No. KX-TCD200FX This unit is Caller ID compatible. To display the caller's phone number, you must subscribe to Caller ID service. Charge the batteries for about 7 hours before initial use. Please read these operating instructions before using the unit and save them for future reference. TCD200FX(e-e). book Page 2 Monday, February 7, 2005 1:19 PM Introduction Introduction Thank you for purchasing a new Panasonic digital cordless phone. For your future reference Attach or keep original receipt to assist with any repair under warranty. [. . . ] 2 Select "Handset Setup", then press {>}. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Ring Delay", then press {>}. 6 Select the desired setting, then press {>}. 7 Enter the desired hour and minute you wish to end this feature by selecting 2 digits for each. 7 Press {ih}. 19 TCD200FX(e-e). book Page 20 Monday, February 7, 2005 1:19 PM Handset Settings Selecting categories to bypass night mode 4 Select "Standby Display", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 5 Select the desired setting, then press {>}. 6 Press {ih}. Note: L If "Base Number" is selected and the current base unit number is 2, "-2-" is displayed. L If "Handset Number" is selected and the current handset number is 2, "[2]" is displayed. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Select Category", then press {>}. 6 Press the desired category numbers, then press {j/OK}. L The selected category number will flash. L To cancel a selected category number, press the number again. The number will stop flashing. Changing the display language 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 7 Press {ih}. Note: L If a call is received from one of the categories set to bypass night mode, only the handset will ring. 3 Select "Display Setup", then press {>}. 4 Select "Select Language", then press {>}. 5 Select the desired language, then press {>}. 6 Press {ih}. Display setup Selecting the standby mode display "Base Number": The current base unit number is displayed. "Handset Number": The current handset number is displayed. "Off": Only the current date and time are displayed. Note: L If you select a language you cannot read, press {ih}, {j/OK}, press {e} 2 times, press {>}, press {v} 2 times, press {>}, press {v}, press {>}, select the desired language, then press {>}. Press {ih}. Changing the display contrast 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Display Setup", then press {>}. 3 Select "Display Setup", then press {>}. 4 Select "Contrast", then press {>}. 20 TCD200FX(e-e). book Page 21 Monday, February 7, 2005 1:19 PM Handset Settings 5 Press {e} or {v} repeatedly to select the desired contrast, then press {>}. 6 Press {ih}. Other options Changing the handset PIN (Personal Identification Number) For security, the handset PIN must be entered when changing certain settings. Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. Call options Turning call bar on/off This feature prohibits making outside calls. When call bar is turned on, only intercom calls and calls to emergency numbers (page 25) can be made. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Call Options", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 4 Select "Call Bar", then press {>}. 5 Enter "0000" (default handset PIN). L If you changed the PIN, enter it (page 21). 3 Select "Other Options", then press {>}. 4 Select "Handset PIN", then press {>}. 6 Select "On" or "Off", then press {>}. [. . . ] I fully charged the batteries, but L Clean the charge contact and charge again (page 7 still flashes. L It is time to replace the batteries (page 9). L You must subscribe to Caller ID service. L Your unit is connected to a telephone line with DSL service. [. . . ]