User manual PANASONIC KX-TD7696

[. . . ] N Flexible Buttons: Used to seize an CO line or perform a feature that has been assigned to the key. O PROGRAM: Used to enter and exit the personal programming mode. P Message/Ringer Lamp: When you receive a call, the lamp flashes red. When someone has left you a message, the lamp stays on red. Document Version 2009-03 3 Settings Settings Speaker volume While in a hands-free conversation Handset/Headset While using the handset or headset volume*1 Ringer volume While on-hook or receiving a call Press Up to increase or Down to decrease the volume. LCD Contrast While on-hook PROGRAM AUTO DIAL STORE AUTO DIAL STORE PROGRAM Ring Tone (CO) PROGRAM OR INTERCOM Press 2 times. *2 AUTO DIAL PROGRAM STORE LCD Backlight While on-hook Automatic*3 PROGRAM AUTO DIAL Always ON STORE Always OFF AUTO DIAL STORE *1 PROGRAM If you hear your own voice through the handset or headset, decrease the volume. [. . . ] Enter the desired mailbox number To send the message immediately (KX-TVA series) (KX-TVS series) Follow the guidance To set the delivery time During playback Repeat Voice Guidance Exit · Consult your dealer for more details regarding feature numbers. · It is possible to assign flexible buttons as feature buttons. · Control panel/button names and descriptions can be found in "Location of Controls" on page 2. Document Version 2009-03 9 Connection Connection Note: In the illustration below, the telephone line cords are routed for wall mounting. When using the stand, refer to "Attaching the Stand" and "Cabling" on page 11 for telephone line cabling. <Back view> The telephone line cord (included) Connect to a PBX. Connect to a digital proprietary telephone -- Digital XDP connection Clamp Headset Recommended: KX-TCA86, KX-TCA91, KX-TCA92 Do not use a KX-T7090 headset. · Consult your dealer for more details about Digital XDP. CAUTION: When connecting a headset When connecting cords · Ensure that the headset cord is wound around the hook to prevent damage to the connector. · Ensure the cords are inserted in the grooves, and are clamped to prevent damage to the connectors. · When mounting the unit on the wall, cords may be routed upwards or downwards by using the appropriate cord clamp located on the back of the unit. 10 Document Version 2009-03 Stand Usage Stand Usage Attaching the Stand Place the catches ( A ) of the stand into hooks located in the unit. Gently push the stand in the direction indicated until it locks into place. The stand will be mounted in the high position. A Removing the Stand Hold the stand with both hands. Gently rotate the stand in the direction indicated until it is released. Cabling When using the stand, ensure that the cords are clamped as shown. Clamp Document Version 2009-03 11 Stand Usage Adjusting from High to Low Position Hold the stand with both hands as shown and rotate the stand in the direction indicated until it locks into the low position ( B ). B 1 Adjusting from Low to High Position Hold the stand with both hands as shown and rotate the stand in the direction indicated until it locks into the high position ( A ). 1 A 12 Document Version 2009-03 Wall Mounting Wall Mounting 1. For information on removing the stand, refer to page 11. Drive the 2 screws (included) into the wall either 83 mm (3-1/4 in) or 100 mm (3-15/16 in) apart, and mount the unit on the wall. · You can find a wall mounting template on page 19. Do not subject this unit to excessive smoke, dust, moisture, mechanical vibration, shock, or direct sunlight. 3) Place the unit on a flat surface. 14 Document Version 2009-03 Important Information WARNING: TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. THIS HANDSET EARPIECE IS MAGNETIZED AND MAY RETAIN SMALL FERROUS OBJECTS. THE USE OF EXCESSIVE SOUND VOLUME THROUGH EARPHONES, HEADPHONES, OR HEADSETS MAY CAUSE HEARING LOSS. DISCONNECT THE TELEPHONE LINE CORD FROM THIS PRODUCT IF THIS PRODUCT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN AUTHORIZED SERVICE CENTER. IMPORTANT NOTICE: · Under power failure conditions, the DPT may not operate. Please ensure that a separate telephone, not dependent on local power, is available for use in remote sites in case of emergency. When you ship the product: Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a postage-paid letter, detailing the symptom to the outside of the carton. DO NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to make repairs. Product service: Panasonic factory service centers for this product are listed in the service center directory. [. . . ] If the unit does not operate according to this manual. Adjust only the controls that are explained in this manual. Improper adjustment of other controls may result in damage and may require service by a qualified technician to restore the product to normal operation. If the unit has been dropped, or damaged. [. . . ]