User manual PANASONIC KXTG1611FR

[. . . ] Please access our online customer survey: http://panasonic. net/pcc/tel/q TG8521E(e). book Page 2 Wednesday, March 17, 2010 3:39 PM Table of Contents Introduction Model composition . 38 Answering System Answering system . 40 Turning the answering system on/off 40 Greeting message . 41 Listening to messages using the base unit . [. . . ] 01289 8333 29 TG8521E(e). book Page 30 Wednesday, March 17, 2010 3:39 PM Programming Important: L When the unit receives a call from a number that is stored in the call barred list, the call is logged in the caller list (page 34) with 7 after the call is disconnected. Storing unwanted callers You can store up to 30 phone numbers in the call barred list by using the caller list or by entering the numbers directly. Important: L You must store the phone number with an area code in the call barred list. From the caller list: W i {V}/{^}: "Yes" i M i {ic} Note: L When editing, press the desired dial key to add, ^ to erase. Changing the base unit PIN (Personal Identification Number) Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, see page 52. 1 2 3 4 1 2 3 1 2 3 {<} (y) {V}/{^}: Select the entry to be barred. i M i I {V}/{^}: "Caller Barred" i M {V}/{^}: "Yes" i M i {ic} 1 (centre of navigator key) i {#}{2}{1}{7} i m Enter the phone number (24 digits max. ). {ic} 1 (centre of navigator key) i {#}{1}{3}{2} Enter the current 4-digit base unit PIN (default: "0000"). i M i {ic} Setting call restriction You can restrict selected handsets from dialling certain numbers. You can assign up to 6 phone numbers to be restricted, and select which handsets are to be restricted. Storing area codes here prevents the restricted handsets from dialling any phone number in that area code. By entering phone numbers: Viewing/editing/erasing bar call numbers 1 2 1 (centre of navigator key) i {#}{2}{5}{6} Enter the base unit PIN (default: "0000"). If a handset moves out of range of its base unit when "Auto" is selected on base unit (page 32), it looks for another base unit to make or receive calls. A base unit and the handsets it communicates with is called a "radio cell". 3 4 Note: L While registering, "Base in registering" is displayed on all registered handsets. Helpline Tel. 01289 8333 31 TG8521E(e). book Page 32 Wednesday, March 17, 2010 3:39 PM Programming L When you purchase an additional handset, refer to the additional handset's installation manual for registration. Selecting a base unit When "Auto" is selected, the handset automatically uses any available base unit it is registered to. When a specific base unit is selected, the handset makes and receives calls using that base unit only. If the handset is out of range of that base unit, no calls can be made. 1 2 3 1 (centre of navigator key) i {#}{1}{3}{9} {V}/{^}: Select the base unit you want to cancel. i M {V}/{^}: "Yes" i M i {ic} Note: L To register a handset to another base unit or to the same base unit again, see page 31. 1 2 1 (centre of navigator key) i {#}{1}{3}{7} {V}/{^}: Select the desired base unit number, or "Auto". i M L The handset starts searching for the base unit. Increasing the range of the base unit You can increase the signal range of the base unit by using a DECT repeater. Please use only the Panasonic DECT repeater noted on page 4. Contact your Panasonic dealer for details. Important: L Before registering the repeater to this base unit, you must turn the repeater mode on. [. . . ] Cause/solution L Disconnect the AC adaptor and telephone line cord from the base unit. Remove the batteries from the handset and leave to dry for at least 3 days. After the handset/base unit are completely dry, reconnect the AC adaptor and telephone line cord. Insert the batteries and charge fully before use. [. . . ]