User manual PANASONIC PT-AE900U REMOTE

[. . . ] Remote control signals for many major home theatre system manufacturers including Panasonic have been recorded into the remote control. You can use the remote control to carry out remote control operations for the other devices simply by selecting the devices' model and code. BRemote control signals can be easily learnt If no codes are available for the devices you are using, or if you would like to customise the functions that you use most frequently, you can use the remote control to learn functions. (The other device's remote control is required in order to carry out learning operations. ) BCustomised display of frequently-used functions on the LCD is possible Function corresponding to the function buttons on the recorded devices can be displayed on the remote control's LCD. [. . . ] BTwo or more equipment codes cannot be entered for the same device. BDevice codes cannot be entered for "PJ". BIf the home theatre system device does not support this function, it will not operate when the buttons are pressed. B When "USER 1-3" is selected 2-1 2-2 Press [ENTER]. Select the device to be set. 1 2 Press [SETUP] for 3 seconds or more. DVD VCR SCREEN TV LIGHTING CBL HVAC SAT RCV AMP Select the device to be set and then press [ENTER]. If "ERROR" is displayed The remote control signal that you are trying to learn has already been registered, so the device code cannot be selected. To set a device code, clear the remote control signal that has been learnt. ( p. 14) 3 B When "DVD, VCR, AMP" is selected Continue to step 3 Select the desired device code while referring to the device code list ( p. 24, 25), and then press [ENTER]. B When "TV/TNR" is selected 2-1 Select the device to be set and then press [ENTER]. When "USER 1-3" is selected Press [SETUP] to finish. TV SAT CBL Note: BIf correct operation is not possible If you find several code numbers when referring to the device code list, try setting one of the other numbers instead. Continue to step 3 8 9 Setting remote control signals for home theatre systems I Setting home theatre system devices when you do not know the device code When recording remote control signals for a home theatre system device when you do not know the device code for that device, you can use the search function to make the settings. B When "USER 1-3" is selected 3-1 Press the up or down button to select "SEARCH?" and then press [ENTER]. Search function The search function transmits a power supply OFF signal, and searches for and sets compatible device codes. 1 2 3 Turn the power on for the home theatre system device that you would like to set. Press [SETUP] for 3 seconds or more. If "ERROR" is displayed The remote control signal that you are trying to learn has already been registered, so the device code cannot be selected. To set a device code, clear the remote control signal that has been learnt. ( p. 14) 3-2 Select the device to be set and then press [ENTER]. Select the device to be set and then press [ENTER]. DVD VCR SCREEN TV LIGHTING CBL HVAC SAT RCV AMP B When "DVD, VCR, AMP" is selected Continue to step 5 4 Continue to step 4 Press [NORMAL]. (Example: When "DVD" is selected) B When "TV/TNR" is selected 5 6 Point the remote control at the home theatre system device and press the up button once. 3-1 Select the device to be set and then press [ENTER]. Repeat step 5 until the power turns off for the home theatre system device. TV SAT CBL Once the power for the home theatre system device turns off, press [ENTER]. To finish, press [SETUP], and then check operation. Continue to step 4 10 11 Setting remote control signals for home theatre systems I Learning remote control signals directly from home theatre system devices If operation is not possible using a device code, you can register other remote control signals for the USER 1-3 buttons. 5 Press the button on the projector's remote control that you would like to record, and then after "LEARNING" is displayed, press the corresponding button on the home theatre system device's remote control. ( Projector's remote ) ( Home theatre system ) control device's remote control When ( Example:button learning the function of the ) playback Note: BRemote control signals that are not infrared-type (wave format) signals cannot be recorded. BIt may not be possible to record some types of signal. After 5 seconds 1 2 Press [SETUP] for 3 seconds or more. Select "USER 1-3" and then press [ENTER]. If "ERROR" is displayed Learning could not be carried out correctly. Return to step 5 and repeat the learning operation. To record another button, repeat step 5. To finish, press [SETUP], and then check operation. (Example: When "USER1" is selected) 3 Select "LEARN?" and then press [ENTER]. Note: BIf the batteries of the remote control are spent, the signals will not be recorded correctly. BEach button must be recorded separately. To edit another character display, repeat steps 4 and 5. When ( Example: is selected ) "USER1" 6 Press [ENTER]. 3 Select "KEY EDIT?" and then press [ENTER]. To finish, press [SETUP]. 4 Press the button to be changed. (Example: When function B has been selected) 16 17 Turning the power for home theatre system devices on and off at once You can use the projector's remote control to turn the power on and off for home theatre system devices that have been recorded in the remote control. 4 5 Select the device to be registered. Note: BAt the time of purchase, a macro for turning the power on and off for PJ, DVD, VCR and AMP all at once is set. (Example: When "USER3" is selected) If a registered device is selected, the display will flash faster. I Using the macro function Press and hold [SYSTEM] for 3 seconds or more. The power for the registered devices will turn on. The length of time required for the macro function to finish operating effectively will vary depending on the number of devices that have been recorded. Press [SYSTEM]. (Example: When "USER3" is selected) If a registered device is selected, the display will flash faster. To register or delete another device, repeat steps 4 and 5. I Setting the macro function Note: B If the distance that the projector's remote control has to operate is too far, or if the remove control receiver of the home theatre system devices are obstructed, this operation may not work correctly. Check the locations and directions of the home theatre system devices to make sure that they can all be operated. Clearing the macro function Press [SYSTEM] once more. 1 2 3 Press [SETUP] for 3 seconds or more. The macro function will be cleared and the display will flash more slowly. Select "USER 1-3" and then press [ENTER]. 6 When you have finished selecting devices, press [ENTER]. (Example: When "USER1" is selected) Select "MACRO?" and then press [ENTER]. To finish, press [SETUP], and then check operation. The display will show the devices that have been recorded by the macro. 18 19 LCD display list I Selected device displays Selected device display PJ DVD VCR TV/TNR AMP USER1/2/3 Corresponding device Projector (PT-AE900E/U) DVD player/DVD recorder Video deck TV/Cable converter/Satellite receiver Audio amplifier/Receiver DVD, VCR, TV/TNR, AMP, other device ( may include devices that cannot be learnt) I Function button guide Function button display HDD DVD DVD/DVD-R DVD LNG REC EPG VCR VCR EXT INP TV/Cable Converter EPG TV/CBL/SAT /Satelite Receiver LNG DVD Audio Ampliflier VCR AMP/RCV /Receiver TV Selected device Corresponding device Description Switch to hard disk (*1) Switch to DVD (*1) Audio select Recording Program list Menu screen clear Input select/Broadcast select Program list Audio select Switch input to DVD (*2) Switch input to VCR (*2) Switch input to TV (*2) I Display messages LCD display CODE ?TIMEOUT Description Indicates that the mode for setting device codes is selected. Displayed when a device code (4 digits) has been selected and entered. Indicates that the mode for deleting learnt remote control signals is selected. Displayed when a learnt function has been deleted. Displayed when code searching of the database is complete. [. . . ] BRemote control signals may vary depending on the device being set, even if the manufacturer is the same. *1: If either the HDD or DVD function button display is blank, operation will be as follows. Selected device DVD Corresponding device DVD/DVD-R Function button display HDD Empty LNG Empty DVD LNG Description Switch to DVD and HDD in that order, or switch directly to HDD Audio select Switch to DVD and HDD in that order, or switch directly to DVD Audio select DVD DVD/DVD-R *2: The DVD, VCR or TV function button displays may operate as follows. (Select 1, 2 and 3 indicates input switches that differ depending on the selected device. ) Selected device AMP/RCV Corresponding device Audio Ampliflier /tuner Function button display DVD VCR TV Description Input switches to Input sequence select (+) or select 1 Input switches to Input sequence select (-) or select 2 Input switches to select 3 I List of display characters Display character Display character Display character Display character Display character Display character Display character Display character Display character Letters Numerals Symbols A K U 1 - B L V 2 + C M W 3 _ D N X 4 E O Y 5 ? F P Z 6 space G Q 7 H R 8 I S 9 J T 0 20 Display character 21 Remote control function list Button display Selected device Device code at time of shipment POWER (PROJECTOR) POWER (SYSTEM) LIGHT Function A Function B Function C LEARN SOURCE SETUP UP DOWN MUTE VOLUME SKIP/INDEX SLOW/SEARCH PJ Backlight Device select Setup Amp mute Amp volume + Amp volume Menu Return Up Down Left Right ENTER NORMAL SHUTTER VIDEO INPUT CMPNT HDMI/PC ASPECT PIC. MODE MEM. LOAD MAIN PIC. ADJUST ADVANCED C. C. M Enter Normal Shutter Video Component HDMI/PC Aspect Picture mode Memory load Main Advanced C. C. M DVD 0490 Power (*1) Backlight HDD DVD LNG Device select Setup Channel + Channel Amp mute Amp volume + Amp volume Skip down Skip up Slow/search Slow/search Stop Pause Play Menu Clear Up Down Left Right Enter Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only VCR 1244 Power (*1) Backlight REC EPG EXT Device select Setup Channel + Channel Amp mute Amp volume + Amp volume Skip (back) Skip (forward) Fast-forward Rewind Stop Pause Play Menu Return Up Down Left Right Enter PROJECTOR POWER - : No signals are sent in the corresponding mode. : Remote control signals can be learnt. (Operation may not be correct for some devices. ) TV/CBL/SAT 1333 (TV) Power (*1) Backlight INP EPG LNG Device select Setup Channel + Channel Amp mute (*2) Amp volume + (*2) Amp volume - (*2) Skip down (*3) Skip up (*3) Slow/search (*3) Slow/search (*3) Stop (*3) Pause (*3) Play (*3) Menu Return Up Down Left Right Enter AMP/RCV 1308 Power (*1) Backlight DVD VCR TV Device select Setup Channel + Channel Mute Volume + Volume Menu Return Up Down Left Right Enter USER1/2/3 (*4) Backlight (*5) (*5) (*5) Device select Setup (*6) (*6) (*6) PROJECTOR POWER CHANNEL + DOWN UP FF REW STOP PAUSE PLAY MENU PROJECTOR RETURN Switches to projector operation Switches to projector operation Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Projector function only Note: *1: Some devices may not allow you to turn the power back on after it has been turned off. [. . . ]