User manual PANASONIC PT-D3500U

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D3500U Read these instructions completely before operating this unit. TQBJ 0178 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D3500U Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. [. . . ] "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" and "DISPLAY LINES" Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. Note · The abovementioned vertical stripes will not appear on the screen when all signals are input. · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. DIGITAL CINEMA REALITY (Only for input of S-Video/ Video/ YPBPR [480i, 576i] signals. ) ON: Set at ON when you need to faithfully capture images shot at 24 frames per second as in movies. OFF: Set at OFF when unnatural images are obtained in the ON status. BLANKING You can perform fine adjustments for blanking if noise appears at the ends of the screen or the image protrudes out of the screen during image projection using a video deck and so on. : Select the UPPER, LOWER, LEFT or RIGHT adjustment. For upper adjustment For lower adjustment CLAMP POS. (For RGB/ YPBPR signals only) Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. The optimal value for the clamp position adjustment · If dark areas are crushed: The optimal value is the point where the dark area is best improved. · If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. Note For left adjustment For right adjustment · The clamp position can be adjusted only when the RGB signal input is applied with RGB1 and RGB2 IN. RASTER POSITION When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. : These adjust the value in the horizontal direction. : These adjust the value in the vertical direction. SXGA MODE This mode takes effect only when SXGA (RGB) signals are input. SXGA : Standard setting SXGA+: Select this when the screen is cut off. 32 Adjusting the audio AUDIO VOLUME AUDIO MUTE SELECT 32 OFF RETRN Changing the display language LANGUAGE ENGLISH Currently chosen language is displayed here. ENTER VOLUME You can adjust the sound volume. : Sound volume increases. SELECT ENTER RETRN AUDIO MUTE You can activate/deactivate audio. OFF: Audio is activated (you can hear sound). Note · No audio will be output when video signal is not displayed. Menus, setting items, adjustment screens, and control button names will be displayed in the language the user chooses. The available languages are: ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, , , , . Note · The projector's on-screen display is set to the English language by default. 33 OPTION1 settings OPTION1 COLOR CORRECTION CONTRAST MODE AUTO SIGNAL OFF BACK COLOR BLACK SUB MEMORY LIST DVI EDID EDID2:PC SELECT ENTER RETRN SUB MEMORY LIST Multiple sets of image adjustment data (PICTURE, POSITION, ADVANCED MENU adjustment values) for the same kind of signal can be registered. SUB MEMORY LIST COLOR CORRECTION OFF : Standard setting USER : The six colors of red, green, blue, cyan, magenta and yellow can be adjusted and registered for each of four signal systems: Video, S-Video, RGB and YPBPR. Press the "ENTER" button to make the detailed settings. COLOR CORRECTION RGB R G B Cy Mg Ye SELECT ADJ 0 0 0 0 0 0 RETRN SELECT STORE RETRN Registering in sub memory Select the sub memory number to be registered using the button. Note · Sub memories range from 1 to 8. The current signal system is displayed. How to select sub memory Select sub memory number (1 to 8) using the buttons. Select "­" if you do not wish to use the sub memory. [. . . ] Contactez le revendeur. Bloc de lampe de rechange, modèle n°: ET-LAD35 (une ampoule) Valeurs nominales: 300 W Bloc de lampe longue durée, modèle n°: ET-LAD35L (une ampoule) Valeurs nominales : 160 W · Des lampes autres que celles spécifiées ci-dessus ne sont pas utilisables. Utilisez la lampe spécifiée. Période de remplacement de la lampe La lampe utilisée comme source lumineuse dans le projecteur a une vie de service de 1 500 heures 1 (quand la sortie de la lampe est HAUT). Il peut arriver que la lampe soit épuisée (ne s'allume pas) à 1 500 heures 1 selon les caractéristiques des lampes individuelles et les conditions de travail (la vie de service des lampes peut être réduite par le nombre d'allumages et les intervalles entre les allumages). Il est donc fortement conseillé aux utilisateurs de conserver une ampoule de rechange. [. . . ]