User manual PANASONIC PT-D5600UL

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D5600U PT-D5600UL PT-DW5000U PT-DW5000UL Read these instructions completely before operating this unit. TQBJ 0200 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. [. . . ] Select "­" if you do not wish to use the sub memory. Note · You cannot select sub memory of a different signal system. CONTRAST MODE There are two modes for adjusting to the operating environment. NORMAL : The contrast is set to normal and the brightness to maximum. HIGH : The contrast is set to maximum and the brightness to normal. How to erase sub memory Select sub memory number (1 to 8) corresponding to sub memory to be erased using buttons. When the indicator of sub memory to be erased flashes, press the ENTER button. AUTO SIGNAL The position where the screen is displayed can be adjusted automatically without pressing the AUTO SETUP button on the remote control each time signals are input when signals are input frequently such as when the projector is used at a conference. ON : Auto setup is performed automatically when the video signals of the images being projected have changed. OFF : The input auto setup function is set to OFF. DVI EDID Set EDID to match the device connected. Mode EDID1 Matching Signal 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i VGA60, SVGA60, XGA50, XGA60, XGA70, XGA85, WXGA768/50, WXGA768/60, SXGA60 BACK COLOR You can set the colors of the screen when no signal is input to the projector. BLACK: Set screen color to black. EDID2:PC 34 OPTION2 settings OPTION2 ID FRONT/REAR DESK/CEILING LAMP SELECT LAMP POWER RS232C SYSTEM INFORMATION FAN CONTROL1 FAN CONTROL2 FUNC1 AUTO POW. OFF PASSWORD SELECT ADJ ALL FRONT DESK DUAL HIGH LAMP SELECT "LAMP SELECT" is used to choose from Single Lamp and Dual Lamp modes depending on user's needs or viewing conditions. In Single Lamp mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified. DUAL : Two lamps are used simultaneously. SINGLE : One of either lamps is used (lamp with shorter operating hours is automatically selected). When one of the above settings is selected, it will take effect after ENTER is pressed. Note · If, in the "SINGLE", "LAMP1" or "LAMP2" mode, one lamp remains off or the currently active lamp exceeds 1 500 hours of cumulative operating time (when "HIGH" is selected as the lamp power setting), the other lamp will light. If, in the "DUAL" mode, one lamp remains off or the currently active lamp exceeds 1 500 hours of cumulative operating time (when "HIGH" is selected as the lamp power setting), the other lamp alone will light. However, if both lamps remain off or the 1 500 hours of cumulative operating time are exceeded, the projector will enter the standby mode. · If only one lamp is installed in the projector, set lamp mode to either "LAMP1" or "LAMP2". "LAMP1" or "LAMP2" is selected. If the corresponding lamp is not installed, the other lamp will turn on. · The colors of the items indicate the status. Green Current setting Cyan Now changing from one status to another Red Lamp that has failed to light White Any other status · If the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently. [. . . ] Une indication sur écran apparaîtra également environ 30 secondes comme indiqué dans le diagramme de droite, recommandant le remplacement de la lampe. (L'indication dans le diagramme de droite disparaîtra après environ 30 secondes ou quand la touche de commande de l'arrière du projecteur ou de la télécommande est opérée. ) Après 1 500 heures 1, l'indication sur écran ne disparaîtra pas à moins d'une opération de la touche MENU. 1 Cette période est de 4 000 heures lorsque des blocs lampes longue durée sont utilisés. 2 Cette période est de 3 800 heures lorsque des blocs lampes longue durée sont utilisés. 65 Remplacement de la lampe Procédure de remplacement de la lampe Attention · Au bout de 1 500 heures (4 000 heures lorsque des blocs lampes longue durée sont utilisés) de fonctionnement pour une même lampe, le projecteur ne peut plus fonctionner que pendant environ 10 minutes. Les étapes à doivent être achevées en moins de dix minutes. Mettez hors tension en suivant la procédure de la page 24, débranchez la fiche électrique et vérifiez que les éléments autour de la lampe ont refroidi. Assurez-vous que le ventilateur est arrêté. [. . . ]