User manual PANASONIC PT-D7500U

[. . . ] DLPTM Based Projector Commercial Use Operating Instructions Model No. PT-D7500U PT-D7600U ON POWER OFF AUTO SETUP RGB 1 RGB 2 AUX SHUTTER VIDEO S-VIDEO SHUT MENU FREEZE PAGE UP ENTER PAGE DOWN ON SCREEN 1 4 7 STD FUNC 2 5 OSD 3 6 SYSTEM SEL D. ZOOM 1 BRIGHT CONTRAST LENS 8 ASPECT 9 0 USER NEXT LIGHT ID ALL ID SET LASER ON/OFF Computer Numetric Projector Read these instructions completely before operating this unit. TQBJ 0113-1 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D7500U / PT-D7600U Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK. [. . . ] · ZOOM: Pictures can be displayed in various magnifications. The user can magnify the pictures with the magnification ranging from 50% to 999%, and the fiducial point is set on the top left of the screen. · 4:3: Pictures are displayed in the aspect ratio of 4:3. · 16:9: Pictures are displayed in the aspect ratio of 16:9. · S4:3: Pictures are scaled down to 75% of the original size without changing the aspect ratio of the input signals. This mode is used when projecting the 4:3 pictures on the 16:9 screen. · HV FIT: Pictures are displayed on the whole panel pixels. If the aspect ratio of the input signals is different from that of the panel, the pictures are displayed by converting it into the panels aspect ratio (4:3 for PT-D7500U and 5:4 for PT-D7600U). · VID AUTO: The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for the video and S-video input. · S1 AUTO: The projector identifies the S1 signal and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for the S-video input. · VID AUTO (PRIORITY): The projector identifies the abovementioned VID or S1 signals and displays the picture by automatically choosing the screen sizes of 4:3 or 16:9 according to the VID if it is detected or S1 signals if a VID is not detected. This function is effective for the S-video input. Note Some size modes are not available for certain types of input signals. · For RGB1 and RGB2 input signals: VID AUTO, S1 AUTO or VID AUTO (PRIORITY) cannot be selected. · For VIDEO input signals: DEFAULT, S1 AUTO or VID AUTO (PRIORITY) cannot be selected. · For an NTSC signal with VIDEO or S-VIDEO input: DEFAULT cannot be selected. 58 Blanking adjustment Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. Procedure of adjustment MAIN MENU PICTURE POSITION LANGUAGE OPTION TEST PATTERN RESISTERED SIGNAL LIST Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "POSITION" with the buttons. :MENU SELECT ENTER:SUB MENU POSITION SHIFT SIZE BLANKING KEYSTONE EDGE BLENDING Press the "ENTER" button. VID AUTO The POSITION screen will be displayed. Select "BLANKING" with the buttons. :MENU SELECT ENTER:SUB MENU BLANKING UPPER LOWER LEFT RIGHT Press the "ENTER" button. 0 0 0 0 The BLANKING adjustment screen will be displayed. Select the desired item for adjustment with the buttons. Adjust blanking with the buttons. The value changes from 0 to 511. :MENU SELECT :ADJUST <When correcting the upper blanking of the screen (top) > Press button to move the blanking zone upward; button to downward. <When correcting the lower blanking of the screen (bottom) > Press button to move the blanking zone upward; button to downward. <When correcting the left hand blanking of the screen (left) > Press button to move the blanking zone to the right; button to the left. <When correcting the right hand blanking of the screen (right) > Press button to move the blanking zone to the right; button to the left. 59 Adjusting the position Clock phase adjustment Clock phase adjustment achieves the best image when the screen flickers or halo is observed around the contour. Procedure of adjustment MAIN MENU PICTURE POSITION LANGUAGE OPTION TEST PATTERN RESISTERED SIGNAL LIST Press the "MENU" button. The MAIN MENU screen will be displayed Select the "POSITION" with the buttons. :MENU SELECT ENTER:SUB MENU POSITION SHIFT SIZE DEFAULT BLANKING CLOCK PHASE 0 INPUT RESOLUTION CLAMP POSITION KEYSTONE EDGE BLENDING Press the "ENTER" button. The POSITION screen will be displayed Select "CLOCK PHASE" with the buttons. Adjust the clock phase with the buttons. The value changes from 0 to 31. :MENU SELECT :ADJUST Note · No optimal value may be obtained if the output of the PC to which the signal input is applied is unstable. · No optimal value may be obtained if the total number of dots is not correct. · The clock phase can be adjusted only when RGB signal input is applied with RGB1, RGB2 IN, and the analog input module (optional: ET-MD95RGB). 60 Adjusting the input resolution Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Procedure of adjustment MAIN MENU PICTURE POSITION LANGUAGE OPTION TEST PATTERN RESISTERED SIGNAL LIST Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "POSITION" with the buttons. :MENU SELECT ENTER:SUB MENU POSITION SHIFT SIZE DEFAULT BLANKING CLOCK PHASE 0 INPUT RESOLUTION CLAMP POSITION KEYSTONE EDGE BLENDING Press the "ENTER" button. The POSITION screen will be displayed. Select "INPUT RESOLUTION" with the buttons. :MENU SELECT ENTER: SUB MENU INPUT RESOLUTION TOTAL DOTS DISPLAY DOTS TOTAL LINES DISPLAY LINES Press the "ENTER" button. 1056 832 666 624 The INPUT RESOLUTION screen will be displayed. Select one of the following items with the buttons and adjust it with the buttons. "TOTAL DOTS", "DISPLAYED DOTS", "TOTAL LINES" and "DISPLAYED LINES" Each item automatically displays a value in response to the type of the input signal. [. . . ] Les étapes 8 à 14 doivent être achevées en moins de dix minutes. 1. Mettez hors tension en suivant la procédure de la page 39 à 40, débranchez la fiche électrique et vérifiez que les éléments autour de la lampe ont refroidi. En utilisant un tournevis Phillips, retirez les 7 vis de la porte d'accès à la lampe située à l'arrière du projecteur. Retirez la porte du logement de lampe du projecteur. Attention · Faites attention de ne pas casser le cliquet situé au centre de la partie inférieure de la porte dÅfaccès la lampe. Vis de fixation Cache de la lampe 4. [. . . ]