User manual PANASONIC PT-DZ8700U

[. . . ] Operating Instructions Functional Manual DLPTM Based Projector Model No. Commercial Use PT-DZ8700U PT-DS8500U PT-DW8300U The projection lens is sold separately. Thank you for purchasing a Panasonic Projector. J Before operating this product, please read the instructions carefully and save this manual for future use. J Before using your projector, be sure to read "Precautions with regard to safety" (Æ pages 8 to 16). TQBJ0341 ENGLISH Important Safety Important Safety Notice Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLPTM Based projector. [. . . ] z The adjustment value for the PT-DS8500U can be changed within a range of 0 to 524 vertically and 0 to 699 horizontally. z The adjustment value for the PT-DW8300U can be changed within a range of 0 to 383 vertically and 0 to 682 horizontally. When correcting the upper blanking of the screen (top) Press to move the blanking zone upward; Press to downward. When correcting the lower blanking of the screen (bottom) 3 ) Press to select [DIGITAL CINEMA REALITY]. z The setting will change as follows each time is pressed. AUTO OFF 25p FIXED : When 576i or 1 080/50i signals are input 30p FIXED : When 480i or 1 080/60i signals are input AUTO OFF 25p FIXED Unforced cinema processing. Forced cinema processing (2 : 2 pulldown) is performed when a 576i or 1 080/50i signal is input. Forced cinema processing (2 : 2 pulldown) is performed when a 480i or 1 080/60i signal is input. 30p FIXED Note When correcting the left hand blanking of the screen (left) Press to move the blanking zone to the right; Press to the left. When correcting the right hand blanking of the screen (right) Press to move the blanking zone to the right; Press to the left. z In [DIGITAL CINEMA REALITY] mode, the image quality will be deteriorated if [30p FIXED] or [25p FIXED] is selected when the signal is not a 2 : 2 pulldown signal. ENGLISH - 63 Settings Performs automatic detection and cinema processing. (factory default) Press to move the blanking zone upward; Press to downward. ADVANCED MENU INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Set the values appropriately for the signal resolution that is being used. EDGE BLENDING The built-in edge blending feature allows multiple projector images to be seamlessly overlapped. 1 ) Press to select [INPUT RESOLUTION]. 2 ) Press <ENTER> button. z The [INPUT RESOLUTION] screen will be 1 ) Press to select [EDGE BLENDING]. 2 ) Press to switch [EDGE BLENDING]. z The setting will change as follows each time is pressed. displayed. 3 ) Press to select [TOTAL DOTS], [DISPLAY DOTS], [TOTAL LINES] or [DISPLAY LINES], and the press to adjust it. z Each item automatically displays a value in OFF ON USER OFF ON When the multi-screens are not going to be used. When the default linear blending ramps are sufficient. When a user-defined blending ramp is required. These ramps can be defined and uploaded to the projector through the RS-232 port. Consult your dealer for details. response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. Note z The vertical stripes will not appear on the all white signal image. z The picture may be distorted during the adjusting operation, but this is not a fault. z The [INPUT RESOLUTION] can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. USER 3 ) Press <ENTER> button. z The [EDGE BLENDING] screen will be displayed. 4 ) Press to specify the area to be adjusted. z To blend the top edge: set [UPPER] to [ON]. z To blend the bottom edge: set [LOWER] to CLAMP POSITION Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. [ON]. z To blend the left edge: set [LEFT] to [ON]. z To blend the right edge: set [RIGHT] to [ON]. Settings 1 ) Press to select [CLAMP POSITION]. [. . . ] z PJLinkTM is a pending trademark in Japan, the United States, and other countries and regions. z HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. z Other types of names such as company names and product names appearing in this instruction manual are trademarks or registered trademarks of their respective holders. The ® and TM marks are not indicated in this instruction manual. Appendix 126 - ENGLISH Ceiling mount bracket safeguards safeguards Ceiling mount bracket When installing the ceiling mount bracket to the projector, install the accessory Drop-prevention bracket (Safety cables) to the projector. [. . . ]