User manual PANASONIC PT-LM1

[. . . ] R LCD Projector Commercial Use Operating Instructions Model No. PT-LM1U POWER INPUT VIDEO RGB AUTO SETUP MENU ENTER FREEZE SHUTTER STD VOLUME INDEX WINDOW D. ZOOM PROJECTOR Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ 0137-1 ENGLISH Dear Panasonic Customer: WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] This detector signal is output by some sources such as wide-vision video decks. B When "ASPECT" is set to "AUTO", the projector recognizes the detector signal and automatically switches the aspect ratio to 16:9. 38-ENGLISH ENGLISH-39 Adjustments and settings POSITION POSITION DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON FRAME LOCK OFF STANDARD SELECT ENTER RETRN Changing the display language NOTE: B If a selected mode does not match the aspect ratio of the input signal, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. B If using this projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that if the aspect ratio (16:9) selection function is used to change the aspect ratio of the screen picture, you may be infringing the rights of the original copyright owner for that program under copyright protection laws. B If a normal (4:3) picture which was not originally intended for wide-screen viewing is projected onto a wide screen, distortion may occur around the edges of the picture, or part of the picture may not be visible. Such programs should be viewed in 4:3 mode to give proper consideration to the aims and intentions of the original program's creator. RESIZING This should normally be set to "ON". (This setting is only for signals which have lower resolutions than the LCD panels. Refer to page 58 for details. ) ON The pixel resolution of the input signal is converted to the same resolution as the LCD panels before being projected. For signals with lower resolutions, gaps in the pixels are automatically interpolated into the picture before it is projected. This may sometimes cause problems with the quality of the picture. OFF The input signal is projected at its original resolution, with no pixel conversion. The projected picture will be smaller than normal, so adjust the zoom setting or move the projector forwards or backwards to adjust the picture size if necessary. If set to "OFF", some features, such as "D. ZOOM" (digital zoom), "KEYSTONE" or "INDEX WINDOW" will not function. Press the F or G button on the projector or remote control unit to select a language, then press the ENTER button to accept the setting. LANGUAGE ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO ENGLISH Indicates the language which is currently set. SELECT ENTER RETRN FRAME LOCK If the picture's condition is bad while a RGB moving picture is projected, set "FRAME LOCK" to "ON". Refer to page 58 for compatible RGB signals. 40-ENGLISH ENGLISH-41 Adjustments and settings Option settings Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting. AUTO SIGNAL This should normally be set to "ON". ON "AUTO SETUP" will be carried out automatically when the input signal is changed. OFF "AUTO SETUP" will not function when the input signal is changed. VGA60/525P VGA60/525P 525P [ DESK/CEILING DESK/CEILING DESK [ VGA60 When a VGA60 or 525p RGB signal is being input, select the signal in accordance with the input signal. OPTION1 OSD ON AUTO SIGNAL ON AUTO KEYSTN ON AUTO RGB/YPB PR VGA60/525P VGA60 SXGA MODE SXGA SELECT ADJ RETRN SXGA MODE SXGA MODE SXGA [ AUTO KEYSTN This should normally be set to "ON". ON During "AUTO SETUP", the angle of tilt of the projector is detected and keystone distortion is corrected automatically. OFF Use this setting when you do not want automatic keystone correction to be carried out during "AUTO SETUP", such as when the screen itself is at an angle. BACK COLOR BLUE [ LAMP POWER LAMP POWER HIGH [ RGB/YPBPR RGB/YPB PR AUTO [ OSD ON The signal name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the signal name to be displayed. NOTE: B The setting for "TV-SYSTEM" will also be displayed when an S-VIDEO/VIDEO signal is being input. RGB [ BLACK This sets the color which is projected onto the screen when no signal is being input to the projector. YPB PR This should normally be set to "AUTO". RGB or YPBPR is selected automatically depending on the synchronising signal status. When HDTV, 525p, 525i, 625p, 625i, 750p, and some VGA480 signals are being input, select "RGB" or "YPBPR" in accordance with the input signal. FRONT/REAR FRONT/REAR FRONT [ REAR This setting should be changed in accordance with the projector setting-up method. [. . . ] B Jeter la lampe usagée de la même manière qu'une lampe fluorescente. B Il faut utiliser un tournevis Phillips pour déposer le bloc de lampe. REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. [. . . ]