User manual PANASONIC PT-D5500E

[. . . ] The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: PT-DZ8700U/PT-DS8500U/PT-D5500E Serial number: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This Projector is designed to operate on 120 V, 60 Hz AC, house current only. Power Supply: CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. [. . . ] z You can correct the distortion ±40 ° from the plane. For a better quality image, installing the projector with a minimum of distortion is recommended. (ET-D75LE5: ±22 ° , ET-D75LE6:±28 ° ) z Some distortion may be retained for lens shift adjustment. z The result of the keystone correction will affect the aspect ratio and the size of the image. Note Settings 62 - ENGLISH ADVANCED MENU z See "Navigating through the menu" (Æpage 49). z See "MAIN MENU" and "SUB MENU" (Æpage 50). BLANKING Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. 1 ) Press to select [BLANKING]. 2 ) Press <ENTER> button. z The [BLANKING] screen will be displayed. DIGITAL CINEMA REALITY Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied. 3 ) Press to select the desired item for adjustment. 4 ) Press to adjust blanking. z The adjustment value for the PT-DZ8700U can 1 ) Press to select [DIGITAL CINEMA REALITY]. 2 ) Press or <ENTER> button. z The [DIGITAL CINEMA REALITY] individual adjustment screen will be displayed. be changed within a range of 0 to 599 vertically and 0 to 959 horizontally. z The adjustment value for the PT-DS8500U can be changed within a range of 0 to 524 vertically and 0 to 699 horizontally. z The adjustment value for the PT-D5500E can be changed within a range of 0 to 383 vertically and 0 to 682 horizontally. When correcting the upper blanking of the screen (top) Press to move the blanking zone upward; Press to downward. z The [CLAMP POSITION] may not be adjusted, depending on the signal. Note 64 - ENGLISH ADVANCED MENU J To display the adjustment marker 7 ) Press to select [MARKER]. 17) Press <ENTER> button. screen will be displayed. z The [BRIGHT OUTSIDE] individual adjustment z When [INTERLOCKED] is set to [OFF], z A marker for adjusting the overlap position appears. The optimal point is the position where the red line of one frame overlaps the green line of the other frame. The blending widths of each projector must be set to the same value. Optimal blending cannot be achieved if the widths are different. The optimal point is where these lines overlap. individual adjustment of [RED], [GREEN] and [BLUE] will be possible. 18) Press to select an item, and press to adjust the setting. Projection range BRIGHT adjustment (right) Edge blending width (right) MAKER BRIGHT BLENDING BRIGHT OUTSIDE BRIGHT INSIDE Green line Red line Press to select [BRIGHT ADJUST]. 10) Press <ENTER> button. displayed. 9) z The [BRIGHT ADJUST] screen will be 11) Press to select [BRIGHT INSIDE]. 12) Press <ENTER> button. z The [BRIGHT INSIDE] individual adjustment z When [INTERLOCKED] is set to [OFF], screen will be displayed. individual adjustment of [RED], [GREEN] and [BLUE] will be possible. 13) Press to select an item, and press to adjust the setting. z Once adjustment is complete, press <MENU> button to return to [BRIGHT ADJUST] screen. 14) Press to select the part of [UPPER], [LOWER], [RIGHT], [LEFT]. 15) Press to adjust the width for correcting the [BRIGHT INSIDE] setting (0 to 255). 16) Press to select [BRIGHT OUTSIDE]. ENGLISH - 65 Settings z The [BRIGHT INSIDE] adjustments are used to match the projector's main-screen-area black levels to the level within the blended area. The [BRIGHT OUTSIDE] adjustments may be used to fine adjust the thin borders on either side of the blend area, but are often not needed. z When a rear screen or screen with a high gain is used, the blended areas may appear to be discontinuous depending on the viewing position. [. . . ] However, use at high altitudes is not possible. Specifications Dimensions <Unit : mm> 8. 5 (11/32") 540 (21 - 1/4") 462 (18 - 7/32") 530 (20 - 7/8") 26 (1 - 1/32") 100 (3 - 15/16") 200 (7 - 7/8") 468 (18 - 7/16") About brand Trademark Acknowledgement z Microsoft® and its logos, Windows®, Windows® XP, Windows Vista®, Windows® 7, and Internet Explorer® are the registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. z Macintosh, Mac OS and Safari are the trademarks of Apple Inc. registered in the United States and other countries. z PJLinkTM is a pending trademark in Japan, the United States, and other countries and regions. [. . . ]