User manual PANASONIC PT-D5700E

[. . . ] DO NOT OPEN MISE EN GARDERISQUE DE CHOC ÉLECTRIQUE. WARNUNG- ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GERÄT NICHT ÖFFNEN. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the Product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. [. . . ] Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "DIGITAL CINEMA REALITY" with the buttons. OFF 75 OFF: Unforced cinema processing AUTO: Performs automatic detection and cinema processing. (factory default) 30p FIXED: Forced cinema processing (2:2 pulldown) is performed when a 480i signal is input. 25p FIXED: Forced cinema processing (2:2 pulldown) is performed when a 576i signal is input. Note · In DIGITAL CINEMA REALITY mode, the image quality will be deteriorated if 30p FIXED or 25p FIXED is selected when the signal is not a 2:2 pulldown signal. FORMAT (To input BETACAM with YCbCr 480i) When receiving a picture of 480i with analog component signal YCbCr input, the input level of Cb and Cr can be switched. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. OFF 75 Select "FORMAT" with the buttons. Switch the signal format with the buttons. · This toggles between SMPTE and BETACAM. <Signal level> Format SMPTE BETACAM Y 700 mV 714 mV Synchronous part :MENU SELECT :CHANGE Cb , Cr ±350 mV ±504 mV 300 mV 286 mV Note · This function is available only when input signals are supplied through the analog RGB input module (ET-MD95RGB). RGB1, RGB2 inputs do not support BETACAM signals. · This function can be switched only when receiving the picture of 480i in the YCbCr mode. It cannot be switched when receiving the picture of signals other than RGB-REALITY mode, RGB mode and 480i. · SMPTE is the factory default. 61 How to use ADVANCED MENU Blanking adjustment Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "BLANKING" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU BLANKING UPPER LOWER LEFT RIGHT Press the "ENTER" button. 0 0 0 0 The BLANKING adjustment screen will be displayed. Select the desired item for adjustment with the buttons. Adjust blanking with the buttons. The value changes from 0 to 511. :MENU SELECT :ADJUST <When correcting the upper blanking of the screen (top) > Press button to move the blanking zone upward; button to downward. <When correcting the lower blanking of the screen (bottom) > Press button to move the blanking zone upward; button to downward. <When correcting the left hand blanking of the screen (left) > Press button to move the blanking zone to the right; button to the left. <When correcting the right hand blanking of the screen (right) > Press button to move the blanking zone to the right; button to the left. 62 Adjusting the input resolution Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "INPUT RESOLUTION" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU INPUT RESOLUTION TOTAL DOTS DISPLAY DOTS TOTAL LINES DISPLAY LINES Press the "ENTER" button. 1056 832 666 624 The INPUT RESOLUTION screen will be displayed. Select one of the following items with the buttons and adjust it with the buttons. "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" and "DISPLAY LINES" Each item automatically displays a value in response to the type of the input signal. Select the "BRIGHT OUTSIDE" with the buttons. Adjust the compensation value (0-255) with the buttons. BRIGHT INSIDE BRIGHT OUTSIDE Note · The BRIGHT adjustment is a function for making the brightening of the BRIGHT level in those areas where the pictures overlap less conspicuous when multi-screens have been configured using edge blending. The optimal point is where, after the BRIGHT INSIDE has been adjusted, the compensation amount is the same for the BRIGHT levels in the areas where the pictures overlap and where the pictures do not overlap. If, after the BRIGHT INSIDE adjustment, only the vicinity of the borders of the areas where the pictures overlap and where the pictures do not overlap becomes bright, proceed to adjust the top, bottom, left and right widths. Alternatively, if only the vicinity of the borders has darkened as a result of the width adjustments, proceed with the BRIGHT OUTSIDE adjustment. · When a rear screen or screen with a high gain is used, the joints may appear to be discontinuous depending on the viewing position. How to switch the input impedance (signal level) of the synchronization signal When the ET-MD95RGB input module (sold separately) is mounted, the user can switch the input impedance (signal level) of the synchronization signal with the analog RGB input. Choose 75 when connecting with the equipment whose synchronization output impedance is 75 such as a signal selector, or switch to HI-Z (TTL) when connecting with the equipment whose synchronization output is TTL such as a video card of a PC. MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU 66 ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. OFF 75 Select "SYNC. TERM" with the buttons. Switch the input impedance (signal level) of the synchronization signal with the buttons. · These buttons toggle between 75 and HI-Z (TTL). SYNC. TERM 75 HI-Z (TTL) Signal level Amplitude: 0. 6V[p-p] to 4. 0V[p-p] High level: 2. 0 V or over Low level: 0. 8 V or lower Input impedance 75 1 k :MENU SELECT :CHANGE Note · Switch the input impedance according to the input signal. · The clock phase and image position may become out of balance during this switching operation. Please make readjustment accordingly. Raster position When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "RASTER POSITION" with the buttons. OFF 75 RASTER POSITION V: H: Press the "ENTER" button. 0 0 The RASTER POSITION screen will be displayed. Adjust the position with the , , and buttons. [. . . ] Une indication sur écran apparaîtra également environ 30 secondes comme indiqué dans le diagramme de droite, recommandant le remplacement de la lampe. (L'indication dans le diagramme de droite disparaîtra après environ 30 secondes ou quand la touche de commande de l'arrière du projecteur ou de la télécommande est opérée. ) Après 1 500 heures 1, l'indication sur écran ne disparaîtra pas à moins d'une opération de la touche MENU. REMPLACER LA LAMPE 1 Cette durée est de 4 000 heures lorsque des blocs lampes longue durée sont utilisés. 2 Cette durée est de 3 800 heures lorsque des blocs lampes longue durée sont utilisés. 113 Remplacement de la lampe Procédure de remplacement de la lampe Attention · Au bout de 1 500 heures (4 000 heures lorsque des blocs lampes longue durée sont utilisés) de fonctionnement pour une même lampe, le projecteur ne peut plus fonctionner que pendant environ 10 minutes. Les étapes 9 à 15 doivent être achevées en moins de dix minutes. 1. [. . . ]