User manual PANASONIC PT-D7700E

[. . . ] You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: PT-D7700E/PT-DS100XE/PT-DW90XE Serial number: WARNING: WARNING: THIS APPARATUS MUST BE EARTHED. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. [. . . ] z No optimal value may be obtained if the total number of dots is not correct. z The [CLOCK PHASE] can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. [GEOMETRY : CURVED] screen will be displayed. z You can adjust the projection images as shown below. ENGLISH - 61 Settings 4 ) Press to select the desired adjustment item, and press to adjust the correction amount. POSITION menu J KEYSTONE menu z VERTICAL KEYSTONE J CURVED menu z LENS THROW RATIO Set to the throw ratio being used (the projection distance divided by the screen width). z VERTICAL KEYSTONE z VERTICAL SUB KEYSTONE z HORIZONTAL KEYSTONE z HORIZONTAL KEYSTONE z VERTICAL ARC z HORIZONTAL SUB KEYSTONE z HORIZONTAL ARC z LINEARITY z VERTICAL BALANCE Settings z HORIZONTAL BALANCE z When [GEOMETRY] setting is set, displayed menu or startup logo might be projected outside of the actual image area. z If both [EDGE BLENDING] (Æpage 65) adjustment and [GEOMETRY] correction are used, [EDGE BLENDING] adjustment cannot be made correctly. Note 62 - ENGLISH POSITION menu KEYSTONE (PT-DW90 only) If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can correct keystone. 1) 2) 3) 4) Press to select [KEYSTONE]. Press to adjust. J KEYSTONE J SUB KEYSTONE J LINEARITY z When [KEYSTONE] setting is set, displayed menu or startup logo might be projected outside of the actual image area. z You can correct the distortion ±40 ° from the plane. For a better quality image, installing the projector with a minimum of distortion is recommended. (ET-D75LE5: ±22 ° , ET-D75LE6:±28 ° ) z Some distortion may be retained for lens shift adjustment. z The result of the keystone correction will affect the aspect ratio and the size of the image. Note ENGLISH - 63 Settings ADVANCED ADVANCED MENUMENU z See "Navigating through the menu" (Æpage 50). z See "MAIN MENU" and "SUB MENU" (Æpage 51). BLANKING Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. 1 ) Press to select [BLANKING]. 2 ) Press <ENTER> button. z The [BLANKING] screen will be displayed. DIGITAL CINEMA REALITY Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied. 3 ) Press to select the desired item for adjustment. 4 ) Press to adjust blanking. z The adjustment value for the PT-D7700E can 1 ) Press to select [DIGITAL CINEMA REALITY]. z To blend the right edge: set [RIGHT] to [ON]. 1 ) Press to select [CLAMP POSITION]. 2 ) Press to adjust. 5 ) Press to toggle [ON] and [OFF]. 6 ) Press to adjust the overlap width and the starting point. z The value changes from 1 to 255. z The optimal value for the clamp position adjustment If dark areas are crushed : The optimal value is the point where the dark area is best improved. If the dark areas are displayed in green : The optimal value is the point where the green areas become black and the crushing effect is rectified. z The [CLAMP POSITION] can be adjusted only when the RGB signal input is applied with RGB1 and RGB2 IN. z The [CLAMP POSITION] may not be adjusted, depending on the signal. Note ENGLISH - 65 Settings ADVANCED MENU J To display the adjustment marker 7 ) Press to select [MARKER]. 17) Press <ENTER> button. screen will be displayed. z The [BRIGHT OUTSIDE] individual adjustment z When [INTERLOCKED] is set to [OFF], z A marker for adjusting the overlap position appears. The optimal point is the position where the red line of one frame overlaps the green line of the other frame. The blending widths of each projector must be set to the same value. Optimal blending cannot be achieved if the widths are different. The optimal point is where these lines overlap. individual adjustment of [RED], [GREEN] and [BLUE] will be possible. 18) Press to select an item, and press to adjust the setting. Projection range BRIGHT adjustment (right) Edge blending width (right) MAKER BRIGHT BLENDING BRIGHT OUTSIDE BRIGHT INSIDE Green line Red line 9) Press to select [BRIGHT ADJUST]. 10) Press <ENTER> button. displayed. z The [BRIGHT ADJUST] screen will be 11) Press to select [BRIGHT INSIDE]. [. . . ] z Macintosh, Mac OS and Safari are the trademarks of Apple Inc. registered in the United States and other countries. z PJLinkTM is a pending trademark in Japan, the United States, and other countries and regions. z HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. [. . . ]