User manual PANASONIC PT-FW300U

[. . . ] Operating Instructions LCD Projector Commercial Use Model No. PT-FW300NTU PT-FW300U (PT-FW300NTU) Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0283-1 ENGLISH Important Safety Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. [. . . ] Press to turn on/off the CLOSED CAPTION. Refer 36 33 34 38 HIGH ALTITUDE MODE If you use the projector at high elevation, the HIGH ALTITUDE MODE setting needs to be ON to set the fan speed high. Press I H to select the required option. OFF ON The fan speed is low. The fan speed is high. NOTE: · Without any operation for 5 seconds, the displayed menu will be disappeared. AUDIO SETTING VOLUME You can adjust the volume of the built-in monaural speaker and VARIABLE AUDIO OUT terminal. I H Decrease Increase NOTE: · At 1 400 m (4 593 ft) above sea level, the setting must be ON. · The loudness of fan noise depends on the HIGH ALTITUDE MODE setting. BALANCE You can adjust to hear the sound played equally through both right and left from VARIABLE AUDIO OUT, or shift the balance so more sound plays through the left or right side. I H More sound plays through the left side More sound plays through the right side EMULATE You can switch to the Panasonic past model's control commands for COMPUTER connection. DEFAULT D3500 D4000 D/W5K series L730 L780 L735 L785 LB/W80 F100, FW100, F200, F300, FW300 models D3500 models D4000 models D5500, DW5000, D5600, DW5100, D5700 models L520, L720 models L750, L780 models L735 models L785 models LB75, LB80, LW80 models Settings IN STANDBY MODE You can switch on/off the sound output in standby mode. OFF ON No sound in standby mode. Output audio in standby mode. AUDIO IN SELECT You can switch the audio output method for COMPUTER1 IN, COMPUTER2 IN and DVI-D IN terminals. DVI COM. AUDIO IN 2 Output audio that is input to the COMPUTER AUDIO 2. AUDIO IN Output audio that is input to the AUDIO IN. COMPUTER1 COM. AUDIO IN 1 Output audio that is input to the COMPUTER AUDIO 1. AUDIO IN Output audio that is input to the AUDIO IN. ENGLISH - 42 PROJECTOR SETUP menu COMPUTER2 COM. AUDIO IN 2 Output audio that is input to the COMPUTER AUDIO 2. AUDIO IN Output audio that is input to the AUDIO IN. FILTER COUNTER RESET After you replaced the Auto Cleaning Filter (ACF), REMAINING FILTER of STATUS in PROJECTOR SETUP need to be reset to "0". Press the ENTER button for more than 3 seconds. The confirmation screen will be displayed. TEST PATTERN You can use the 7 different test patterns to adjust the focus of the image. See "Lens shift and positioning" on page 17. Press the ENTER button to display the test pattern 1. Press I H to select the required test pattern. Press the MENU or RETURN button to return to the previous menu, or press repeatedly to escape from the menu mode. 2. Select OK by pressing I, then press the ENTER button. Display the STATUS and confirm the figure. NOTE: · When the projector and/or the screen is tilted, adjust the focus at the center of the image. The upper and lower edge might be out of focus. · When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu. INITIALIZE ALL You can reset all of the customized settings to the factory defaults except NETWORK, RUNTIME and REMAINING FILTER of STATUS in PROJECTOR SETUP menu. Select OK by pressing I, then press the ENTER button. Turn off the power by pressing the power button. Switch off the MAIN POWER button to reset the projector. [. . . ] haut à gauche de l'écran, et attend votre réponse. Pour le supprimer immédiatement, appuyer sur n`importe quelle touche. Plus de 6000 heures REMARQUE: · Les durées indiquées, de 5000 et 6000 heures, sont des estimations basé sur certaines conditions et ne représentent en aucun cas des durées garanties. · Pour plus d'informations à propos des caractéristiques de l'unité de la lampe, telles que la durée de garantie, se reporter aux instructions fournies avec l'unité de la lampe. FRANÇAIS - 69 Information Importante Remplacement de l'unité de la lampe Remplacement de l'unité de la lampe Procédure de remplacement Retirer et remplacer la lampe 1. Dévisser à l'aide d'un tournevis cruciforme les 2 vis de fixation du couvercle de la lampe à l'arrière du projecteur jusqu'à ce qu'elles tournent librement, puis retirer le couvercle de la lampe. [. . . ]