User manual PANASONIC PT-L780E

[. . . ] Model number: PT-L780NTU / PT-L780E Serial number: CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. If you are unable to insert the plug into the outlet, contact an electrician. [. . . ] (The projected image is contracted vertically) Press the H button. NOTE: B If you press the AUTO SETUP button after correcting the keystone distortion manually, the automatic keystone correction function will operate and the corrected picture will return to its previous incorrect condition. In addition, if you change the input signal and press the AUTO SETUP button, the keystone correction may be cancelled depending on the type of signal and the angle of tilt of the projector. To prevent them from happening, you can set "AUTO KEYSTONE" in the OPTION menu to "OFF" B The greater the correction of keystone distortion amount, the more the picture OSD POSITION Press the I or H buttons to move the OSD position. S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen. ) ASPECT This setting is only valid for an SVIDEO/VIDEO signal and a YPBPR signal in 525i (480i), 525p (480p) and 625i format. When a 4:3 signal is being input KEYSTONE Before carrying out keystone correction, 1) adjust the forward/back angle of tilt of the projector by pressing the adjuster buttons and 2) press the AUTO SETUP buttons to correct vertical keystone distortion. (pages 28 and 29) The vertical keystone distortion will be automatically corrected by the projector's automatic setup function [ AUTO 4:3 16:9 S4:3 40 41 Basic Operation Press the F button. quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. B The picture size will also change when correction of keystone distortion is carried out. B The range of keystone correction varies depending on the type of signal being input. If you make an adjustment that is outside the allowable range, the setting will not be changed. (page 14) FRAME LOCK If the picture's condition is bad while a RGB moving picture signal is projected, set the FRAME LOCK to "ON". Refer to page 61 on compatible RGB signals. 42 43 Basic Operation Option settings Select the item pressing the F or G buttons on the remote control unit or the projector. Press the I or H buttons to adjust the selective items. To make the SHUTTER or WEB PASSWORD (PT-L780NTU only) functions work, press the ENTER button. BACK COLOR OSD ON The current input name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the current input name to be displayed. This sets the colour which is projected onto the screen when no signal is being input to the projector. FRONT/REAR This setting should be changed in accordance with the projector setting-up method. Set to "FRONT" when using a normal reflective screen with the projector positioned in front of the screen, and set to "REAR" when using a translucent screen with the projector positioned behind the screen. for the lamp unit will be reset to zero. NOTE: B The lamp's operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off). FAN CONTROL If using of this projector at high elevations (above 1 400 m), set the FAN CONTROL to "HIGH". OPTION SHUTTER OSD AUTO KEYSTONE RGB/YPbPr RGB2 SELECT BACK COLOR FRONT/REAR DESK/CEILING LAMP POWER LAMP RUN TIME NEXT PAGE @ SELECT:[^][@] ADJUST:[{][}] AUTO KEYSTONE OFF OFF RGB INPUT BLUE FRONT DESK LOW ON ON YPbPr OUTPUT BLACK REAR CEILING HIGH 10 H ENTER:[ENTER] ESC:[MENU] OPTION PREVIOUS PAGE ^ FAN CONTROL WEB CONTROL WEB STANDBY WEB PASSWORD CONTROL KEY FUNC1 SET ID AUTO POWER OFF STANDARD OFF OFF OFF MUTE ALL DISABLE HIGH ON ON ON KEYSTONE RGB/YPbPr This setting is valid when 750p, HDTV60, HDTV50, 525p, 625i and 525i signals are being input. Select the setting in accordance with the input signal. The RGB/YPbPr item is displayed when an RGB1 IN, RGB2 IN or RGB 3 IN connectors has a signal being input. LAMP POWER This setting changes the lamp brightness. When set to "LOW", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. [. . . ] REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. Numéro de produit du bloc de lampe: ET-LA780 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. Avant de faire le nettoyage et l'entretien, s'assurer de débrancher la fiche du cordon d'alimentation de la prise de courant. Essuyer le boîtier avec un tissu doux et sec. Si le boîtier est très sale, imbiber le chiffon dans de l'eau avec un peu de détergent neutre, bien essorer le chiffon, puis essuyer le boîtier. Après le nettoyage, sécher le boîtier à l'aide d'un chiffon sec. [. . . ]