User manual PANASONIC PTLB1

[. . . ] To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Important Information WARNING: Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. WARNING: 1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. 2.  prevent electric shock, do not remove cover. [. . . ] Make sure to set the correction width for the sets to join as the same value. Optimal joining is not possible with the sets with different correction widths. The optimal point is the point at which these lines 18) Press ▲▼ to select [BRIGHT OUTSIDE]. 19) Press the <ENTER> button. zzThe [BRIGHT OUTSIDE] individual adjustment screen is displayed. zzIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] can be adjusted individually. 20) Press ▲▼ to select an item, and press ◀▶ to adjust the setting. [OUTSIDE AREA] (Right) Projection range Edge blending [WIDTH] (Right) [MARKER] (Red) Edge blending [START] (Right) 〔[MARKER] (Green)〕 [BRIGHT OUTSIDE] [BRIGHT INSIDE] Green line Red line 9) Press ▲▼ to select [GAMMA]. 10) Press ◀▶ to switch [GAMMA]. [2. 2] [1. 8] zzThe setting will change as follows each time you press the button. [2. 0] 11) Press ▲▼ to select [BRIGHT ADJUST]. 12) Press the <ENTER> button. Settings zzThe [BRIGHT ADJUST] screen is displayed. 13) Press ▲▼ to select [BRIGHT INSIDE]. 14) Press the <ENTER> button. zzThe [BRIGHT INSIDE] individual adjustment screen is displayed. zzIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] can be adjusted individually. Note zz[BRIGHT ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to notice when [EDGE BLENDING] is used to configure multiple screens. The optimal point of the correction is set by adjusting [BRIGHT INSIDE] so the black level of the overlapping image area will be the same level as the non-overlapping area. If the bordering part of the part where the image is overlapping and the non-overlapping part gets brighter after adjusting [BRIGHT INSIDE], adjust the width of the top, bottom, left, or right. zzThis adjustment should be carried out by a person who is familiar with the projector or by a service person because a high level of skill is required to make a successful adjustment. zzPressing the <DEFAULT> button will restore the factory default settings for all items. zzWhen [COLOR MATCHING] is set to other than [OFF], [AI] and [COLOR CORRECTION] are fixed to [OFF], and [COLOR TEMPERATURE] is fixed to [USER]. (However, [WHITE BALANCE HIGH] cannot be adjusted. ) zzIf [3COLORS:WHITE] is selected, only [GAIN] can be adjusted. Settings 58 - ENGLISH [DISPLAY OPTION] menu To ■■ use a colorimeter to adjust the color matching Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], and [WHITE] to desired colors. [COLOR CORRECTION] Colors can be adjusted and registered for each input signal format. zInputting the current luminance and z chromaticity coordinates 1) Press ▲▼ to select [COLOR MATCHING]. 3) Press the <ENTER> button. zzThe [MEASURED MODE] screen is displayed. 1) Press ▲▼ to select [COLOR CORRECTION]. 2) Press ◀▶ to switch [COLOR CORRECTION]. [OFF] Standard setting For each of the four signal formats, VIDEO, S-VIDEO, RGB, and YCBCR/YPBPR, six colors including red, green, blue, cyan, magenta, and yellow can be adjusted and registered. Press the <ENTER> button to set details. [USER] 4) Press ▲▼ to select [MEASURED DATA]. 5) Press the <ENTER> button. zzThe [MEASURED DATA] screen is displayed. [CONTRAST MODE] There are two modes. Set according to the operating environment. 6) Measure the luminance (Y) and the chromaticity coordinates (x, y) using the colorimeter. 7) Press ▲▼ to select a color, and press ◀▶ to adjust the setting. 8) Once all the input is completed, press the <MENU> button. [. . . ] 1 set (BNC x 5) <RGB 1 IN> terminal RGB signals 0. 7 V [p-p] 75 Ω (SYNC ON GREEN: 1. 0 V [p-p] 75 Ω) SYNC/HD TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible Y: 1. 0 V [p-p] including synchronization signal, PBPR: 0. 7 V [p-p] 75 Ω PTLB1 PTLB1L YPBPR signals 1 set, high-density D-Sub 15p (female) <RGB 2 IN> terminal RGB signals 0. 7 V [p-p] 75 Ω (SYNC ON GREEN: 1. 0 V [p-p] 75 Ω) SYNC/HD TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible Y: 1. 0 V [p-p] including synchronization signal, PBPR: 0. 7 V [p-p] 75 Ω YPBPR signals <DVI-D IN> terminal Terminals <HDMI IN> terminal <VIDEO IN> terminal <S-VIDEO IN> terminal <SERIAL IN>/ <SERIAL OUT> terminal <REMOTE 1 IN>/ <REMOTE 1 OUT> terminal <REMOTE 2 IN> terminal <LAN> terminal Power cable length Outer case 1 set, DVI-D 24 p single link, DVI 1. 0 compatible, HDCP compliant 1 set, HDMI 19 pin, (HDCP and Deep color compatible) 1 set, BNC 1. 0 V [p-p] 75 Ω 1 set, Mini DIN 4 p Y 1. 0 V [p-p], C 0. 286 V [p-p] 75 Ω S1 signal compatible D-Sub 9 p, each set, RS-232C compatible, for computer control M3 stereo mini jack, each set for remote control (wired)/for projector serial control 1 set D-Sub 9 p (female) for contact control 1 set, (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX) 3. 0 m (118-1/8") Molded plastic Width: 498 mm (19-19/32") Height: 175 mm (6-7/8") (with minimum feet length) Depth: 466 mm (18-11/32") (including the standard zoom lens) Approx 16. 3 kg (35. 9 lbs. )*3 (including the standard zoom lens) Width: 498 mm (19-19/32") Height: 175 mm (6-7/8") (with minimum feet length) Depth: 423 mm (16-21/32") Approx 15. 4 kg (34 lbs. )*3 Dimensions Weight Operating environment Power supply Remote control Operating range Weight Dimensions Operating environment temperature*4: 0°C (32°F) to 45°C (113°F) Operating environment humidity: 20% to 80% (no condensation) DC 3 V (AA/R6 battery x 2) Within 30 m (98'5") (when operated directly in front of signal receiver) 134 g (4. 7 ozs. )(including batteries) Width: 51 mm (2") Height: 176 mm (6-15/16") Depth: 22. 7 mm (29/32") zzThe model numbers of accessories and optional components are subject to change without notice. ENGLISH - 121 Appendix *1: Value for the supplied standard zoom lens. The indicated value is an average value of the overall projector at factory default, and is written in accordance with the specification form of the JIS X 6911:2003 data projector. Measurement methods and measuring conditions comply with Appendix 2. *2: The size is maximum 200" when ET-DLE055 lens is used. [. . . ]