User manual PANASONIC PT-LB30E

[. . . ] Model number: PT-LB30E / PT-LC76U / PT-LC56U Serial number: WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Use the I and H buttons to adjust so that the noise level is least noticeable. NOTE: B If signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out. When using the 16:9 screen. S1 video signals B S1 video signals are a type of video signal with an aspect ratio of 16:9 which include a detector signal. This detector signal is output by some sources such as wide-vision video decks. If the AUTO setting above is selected, this projector will recognise the detector signal and automatically switch the aspect ratio to 16:9 in order to project the picture. POSITION POSITION ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER RETRN When a squeezed signal is being input. (The projected image is contracted vertically) [ 38-ENGLISH ENGLISH-39 Adjustments and settings AUTO (S-VIDEO only) When an S1 video signal is input to the S-VIDEO terminal, the aspect ratio is changed automatically to project a 16:9 picture. 4:3 The input signal is projected without change. 16:9 The picture is compressed to a ratio of 16:9 and projected. When a 4:3 signal is being input [ FRAME LOCK If the picture's condition is bad while a RGB moving picture signal is projected, set the FRAME LOCK to "ON". Refer to page 58 on compatible RGB signals. 40-ENGLISH ENGLISH-41 Adjustments and settings NOTE: B This projector is equipped with an aspect ratio selection function. However, if a mode which does not match the aspect ratio of the input signal is selected, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. When set to "LOW", the BLACK 42-ENGLISH ENGLISH-43 Adjustments and settings SXGA MODE This setting should be changed in accordance with the projector setting-up method. Set to "DESK" when setting up the projector on a desk or similar, and set to "CEILING" when suspending the projector from the ceiling using the ceiling bracket which is sold separately. luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp's operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the LAMP POWER to "LOW". CONTROL KEY CONTROL KEY ON [ Setting up the SECURITY function This projector is equipped with a security function. A password input screen can be displayed, or a company URL can be set up and displayed at the bottom of the projected image. Use the F and G buttons on the projector or remote control unit to select SECURITY, then press the ENTER button. OFF To disable the buttons on the projector, set CONTROL KEY to "OFF". A confirmation screen will then be displayed. Select "OK" by using I and H buttons. To use the buttons on the projector, set to "ON" by using the remote control unit. (page 14) INPUT PASSWD The password input screen can be displayed when the power is turned on. All of the controls other than the POWER button are disabled unless the password is entered correctly. [. . . ] Numéro de produit du bloc de lampe: ET-LAC80 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. Notes sur l'utilisation Afin d'obtenir la meilleure qualité d'image Fermer les rideaux ou les volets de toutes les fenêtres et éteindre les lampes fluorescentes situées à proximité de l'écran afin que la lumière extérieure ou la lumière des lampes intérieures n'éclaire pas l'écran. Ne pas toucher aux surfaces de la lentille avec les mains nues. Si la surface de la lentille est salie par des empreintes digitales ou autre, ceci sera agrandi et projeté sur l'écran. D'ailleurs, lorsque le projecteur n'est pas utilisé, rétracter la lentille, puis la couvrir à l'aide du capuchon d'objectif fourni. [. . . ]