User manual PANASONIC SC-ALL2GN

[. . . ] Operating Instructions <Full version> Wireless Speaker System Model No. SC-ALL2 Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. RQT0A27-1B Table of contents Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unit care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can preset stations when playback using internet radio app “AllPlay Radio”. Qualcomm® AllPlay™ Radio powered by TuneIn is a product of Qualcomm Connected Experiences, Inc. You can preset up to 6 channels. ≥ A station previously stored is overwritten when another station is stored in the same channel preset. Preparation ≥ Make sure that the network is connected to the Internet. ≥ Connect a device with an “AllPlay Radio” app installed to the same network as this unit. 1 Turn this unit on. ≥ Check that the network indicator (blue) lights up. – If the network indicator is blinking in blue and red, wait until the blinking stops. 2 Start the app “AllPlay Radio”, and select a station to playback. ≥ Always use the latest version of the app. 3 Touch and hold one of [1] to [6] on the unit for at least 4 seconds to preset the selected station. e. g. , “P1” blinks 3 times when [1] is selected. - 28 - ∫ Listening to a preset channel Touch one of [1] to [6] on the unit. ≥ If the selected preset channel has not been preset or this unit is not connected to the network, “no:ch” is displayed. - 29 - Bluetooth® operations By using the Bluetooth® connection, you can listen to the sound of the Bluetooth® audio device wirelessly. ≥ Refer to the operating instructions of the Bluetooth® device for further instruction on how to connect a Bluetooth® device. Connecting via Bluetooth® menu Preparation ≥ Turn on the Bluetooth® feature of the device and place the device near this unit. ∫ Bluetooth® pairing 1 Touch [ ≥ If [ ]. ] for at least ] blinks fast, go to step 3. 2 To enter pairing mode, touch and hold [ 2 seconds. ≥[ ] will blink fast. 3 Select “SC-ALL2” from the Bluetooth® device’s Bluetooth® menu. ≥ The MAC address (e. g. , 6C:5A:B5:B3:1D:0F) may be displayed before “SC-ALL2” is displayed. ≥[ ] lights up and the device is connected to this unit. - 30 - ∫ Connecting a paired Bluetooth® device 1 Touch [ ≥[ ]. ] blinks slowly. ≥ If [ ] lights, a Bluetooth® device is already connected with this unit. (l below) 2 Select “SC-ALL2” from the Bluetooth® device’s Bluetooth® menu. 3 Start playback on the Bluetooth® device. ∫ Disconnecting a Bluetooth® device Touch and hold [ ≥[ ] blinks slowly. ] for at least 2 seconds. ≥ If prompted for the passkey, input “0000”. ≥ You can register up to 8 devices with this unit. If a 9th device is paired, the device that has not been used for the longest time will be replaced. ≥ When [ ] is selected as the source, this unit will automatically try and connect to the last connected Bluetooth® device. If the connection attempt fails, try to establish a connection again. ≥ When the unit is selected as the speakers powered by AllPlay or DLNA, the audio source will change to the network. ≥ Bluetooth® cannot be selected as the audio source when the unit is waiting for the WPS PUSH or WPS PIN code connection. ≥ This unit can only be connected to one device at a time. ≥ When enjoying video contents with this function, the video and audio output may not be synchronised. - 31 - Bluetooth® standby This function allows you to connect a paired Bluetooth® device when this unit is in standby mode. ≥ This unit will be turned on automatically when you connect a paired Bluetooth® device. – If this function is set to “On”, the standby power consumption will increase. 1 Touch and hold [ ] and [1] for at least 4 seconds. 2 Touch [VOL –] or [VOL +] to select “On”. 3 Touch [DISP] to confirm the setting. ≥ To turn the function off, select “OFF” in step 2. ≥ The factory default is “OFF”. - 32 - Bluetooth® transmission mode You can change the transmission mode to prioritise transmission quality or sound quality. ≥ If a Bluetooth® device is already connected, disconnect it. 1 Touch and hold [ ] and [2] for at least 4 seconds. 2 Touch [VOL –] or [VOL +] to change the setting. Ll: 1: Emphasis on connectivity Ll: 2: Emphasis on sound quality 3 Touch [DISP] to confirm the setting. ≥ Select “Ll: 1” if the sound is interrupted. [. . . ] Other trademarks and trade names are those of their respective owners. Google Play and Android are trademarks of Google Inc. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. App Store is a service mark of Apple Inc. The Wi-Fi CERTIFIED™ Logo is a certification mark of Wi-Fi Alliance®. [. . . ]