User manual PANASONIC SC-HC25DBEB

[. . . ] SAFETY PRECAUTIONS Operating Instructions Placement Set the system up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the service life of the system. Place it at least 15 cm away from wall surfaces to avoid distortion and unwanted acoustical effects. Do not place heavy items on the system. Sales and Support Information Customer Care Centre · For customers within the UK: 0844 844 3852 · For customers within Ireland: 01 289 8333 · Visit our website for product information www. panasonic. co. uk · E-mail: customer. care@panasonic. co. uk Direct Sales at Panasonic UK · For customers: 0844 844 3856 · Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday­Thursday 9:00 a. m. ­ 5:30 p. m. , Friday 9:30 a. m. ­ 5:30 p. m. [. . . ] Do this step again to program other tracks. Click! 1 Press and hold [RADIO, EXT-IN] on the 3 Press [4/9] to start playback. 2 Press [R, T] to select the desired album. 3 Press [6] and then press the numeric buttons to select the desired track. 8 main unit and [2] on the remote control until "REMOTE 2" is shown. 4 seconds. CLOCK AND TIMERS 1 Press [CLOCK/TIMER] to select "#PLAY 1", "#PLAY 2" or "#PLAY 3". start time. 2 Press and hold [OK] and [2] for a minimum of Setting the clock This is a 24-hour clock. 2 Press [CD] and then press [4/9] to start 2 Within 10 seconds, press [R, T] to set the 3 Press [OK]. 4 Do steps 2 and 3 again to set the end time. To start the timer playback. Keep fingers away from the sliding door when it is closing. Press [R, T]. 1 Press [CLOCK/TIMER] to select "CLOCK". 2 Within 10 seconds, press [R, T] to set the time. 12 TROUBLESHOOTING GUIDE Stop playback Pause playback Skip album Skip track Search through track 4 Press [OK]. Do steps 2 through 4 again to program other tracks. Press [2] or [6] when "PGM" is shown in the stop mode. To check while programming, press [PROGRAM] two times after "PGM" is shown, then press [2] or [6]. Within 5 seconds, press [8] again. 5 Press [4/9] to start playback. Cancel program mode Replay the program Check program contents 3 Press [OK]. Press [CLOCK/TIMER] to show the clock for a few seconds. Note: Reset the clock regularly to maintain accuracy. Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated do not solve the problem, consult your dealer for instructions. 5 Press [#, PLAY] to start "#PLAY 1", "#PLAY 2" or "#PLAY 3". Common problems No operations can be done with the remote control. · Examine that the battery is installed correctly. · Switch off the system, determine and correct the cause, then switch the system on again. It can be caused by straining of the speakers through excessive volume or power, and when using the system in a hot environment. A "humming" sound can be heard during playback. · An AC mains lead or fluorescent light is near the cables. Keep other appliances and cords away from the cables of this system. Main unit displays "NO PLAY" · Examine the content. · This system can read and play up to 255 albums or folders (audio and non-audio). [. . . ] 2 Insert a compatible dock adapter. iPhone (not included) Note: If no station is detected, "SCAN FAILED" is shown. Auto clock adjustment 1 Decrease the volume and connect the USB mass storage device to the USB port. then press [4/9] to start playback. All the settings are set back to the factory preset. It is necessary to set the memory items again. Memory presetting 20 stations can be preset. 1 Press [RADIO MENU] to select "AUTO CLOCK ADJ". 2 Press [RADIO, EXT-IN] to select "USB" and Stop playback Press [8] during playback. OR Press [8] two times to stop the playback fully. 2 Press [Y, U] to select "ON ADJUST" and then press [OK]. [. . . ]