User manual PANASONIC SC-NC9

[. . . ] Place the front, center, and surround speakers at approximately the same distance from the seating position. Center speaker Step 1: Positioning the speakers Front speakers Speakers are designed identically so that no left or right channel orientation is necessary. (SB-PF9/ SB-PF6) (SB-PC9) (SB-PF9/ SB-PF6) Front speaker (left) 3 0 o 3 0o Front speaker (right) Subwoofer Place on either side of the television, on the floor or a sturdy shelf to reduce vibration. SC-NC9 Center speaker Do not place the center speaker directly on the television as vibration may cause it to fall or disrupt the picture. SC-NC9 Surround speakers Place on the side of or slightly behind the seating area. (SB-WNC9) 1 2 0o Subwoofer Surround Surround speaker speaker (right) (left) (SB-PS9) (SB-PS9) Note · You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods. · Reduce the volume in the following cases to avoid damage. [. . . ] 1 Drive a screw (not included) into the wall. 30 - 35 mm Positioning the speakers for Bi-Amp TS mode (SB-PS9) (SB-PS9) 7. 5 - 9. 4 mm 5 - 7 mm 3. 0 - 4. 0 mm Center speaker (SB-PC9) (SB-PF9) (SB-PF9) Surround speaker (left) on top of front speaker (left) 3 0 o 3 0o Surround speaker (right) on top of front speaker (right) (SB-WNC9) Subwoofer 2 Fit the hole securely onto the screw(s). The wall or pillar on which the speaker is to be attached should be capable of supporting 10 kg per screw. Consult a qualified building contractor when attaching the speaker to a wall. Improper attachment may result in damage to the wall and speaker. 220 mm 3 Simple setup STEP Connecting the speakers SC-NC9 Speaker cables · Front (2 x 1. 5 m) 1 Speaker cable sticker · Subwoofer (1 x 2. 5 m) · Attach the speaker cable stickers to make SC-NC9 Supplied · Center (1 x 2 m) connection easier accessories · Surround (2 x 7 m) S UB WOOFER CENTER SURROUND Rc h SURROUND Lch FRONT Rch FRONT Lch 6 6 5 5 4 4 3 3 2 2 1 1 S UB WOOFER CENTER SURROUND Rc h SURROUND Lch FRONT Rch FRONT Lch 6 5 4 3 2 1 Note Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers. SC-NC9 Step 2: Connecting the speakers CENTER Insert the wire fully. +: Red ­: Black Speaker cable sticker CENTER 5 CENTER 5 FRONT (L) FRONT Lch 1 FRONT Lch 1 FRONT (R) FRONT Rch 2 FRONT Rch 2 SUB WOOFER SUB WOOFER SURROUND (L) SURROUND Lch 3 SURROUND Lch 3 SURROUND (R) AC IN SURROUND Rch 4 (75 ) FM ANT SURROUND Rch 4 AM ANT LOOP EXT This unit SPEAKERS R L R L + TO SB-PS9 SURROUND (3 ) TO SB-PF9 FRONT (3 ) TO SB-PC9 CENTER (3 ) TO SB-WNC9 SUB-WOOFER (3 ) Insert the wire fully. +: Red ­: Black SC-NC6 FRONT (L) FRONT (R) RQTX0072 AC IN (75 ) FM ANT AM ANT LO LOOP LOOP EXT 4 This unit SPEAKERS R L + TO SB-PF9 FRONT (3 ) TO SB-WNC9 SUB-WOOFER (3 ) Insert the wire fully. +: Red ­: Black FRONT Lc h FRONT Lc h 1 FRONT Rch FRONT Rch 2 SURROUND Lch SURROUND Lch 3 SURROUND Rch SURROUND Rch 4 CENTER CENTER 5 SUB WOOFER SUB WOOFER 6 SUBWOOFER 6 6 +: Red ­: Black Insert the wire fully. SUBWOOFER +: Red ­: Black Insert the wire fully. Supplied accessories AM loop antenna FM indoor antenna AC mains lead Video cable · Connect the AC mains lead after all other connections are complete. Conserving power The unit consumes a small amount of power (approx. To save power when the unit is not to be used for a long time, unplug it from the household mains socket. You will need to reset some memory items after plugging in the unit. AM loop antenna Do not connect the unit through a video cassette recorder, because the picture may not be displayed correctly due to copy guard protection. · Turn the television off before connecting, and refer to the television's operating instructions. Video cable (included) VIDEO OUT FM indoor antenna Affix this end of the antenna where reception is best. Adhesive tape Click! S VIDEO OUT VIDEO IN COMPONENT VIDEO OUT B PR Television AC mains lead To household mains socket AC IN REC OUT AUX R L AM ANT LOOP EXT (75 ) FM ANT While pushing, insert the wire fully. SPEAKERS R L R L + TO SB-PF9 FRONT (3 ) TO SB-PC9 CENTER (3 ) TO SB-WNC9 SUB-WOOFER (3 ) - BE SURE TO READ THE CAUTION FOR AC MAINS LEAD ON PAGE 2 OF THE OPERATIONS GUIDE BEFORE CONNECTION. Insertion of connector Even when the connector is perfectly inserted, depending on the type of inlet used, the front part of the connector may jut out as shown in the drawing. However there is no problem using the unit. Appliance inlet Connector RQTX0072 Approx. 3. 5 mm Step 3: Television, antenna and AC mains lead connections Stand the antenna up on its base. Place the antenna where reception is the best. Keep loose antenna cord away from other wires and cords. VIDEO OUT terminal Simple setup STEP Television, antenna and AC mains lead connections 5 Simple setup Other television connections · Do not connect the unit through a video cassette recorder, because the picture may not be displayed correctly due to copy guard protection. · Turn the television off before connecting, and refer to the television's operating instructions. [. . . ] · This connection will also enable you to play audio from your television through your stereo system ( Using other equipment, page 39, Operations Guide). · Do not use the HDMI cable when you use the scart cable for the connection. TO SB-PS9 SURROUND (3 ) S VIDEO OUT Y VIDEO OUT COMPONENT VIDEO OUT PB PR REC OUT AUX R L A AM A ANT LO LOOP EXT (75) FM ANT + RQTX0072 TO SB-PF9 FRONT (3 ) TO O SB-PC9 P CENTER T (3 ) TO SB-WNC9 SUB-WOOFER (3 ) 6 Using an S VIDEO OUT terminal Television S-VIDEO IN S Video cable (not included) Back of this unit S VIDEO OUT The S VIDEO terminal achieves a more vivid picture than the VIDEO OUT terminal by separating the chrominance (C) and luminance (Y) signals. (Actual results depend on the television. ) AV OUT AV Using a COMPONENT VIDEO OUT terminal Television COMPONENT VIDEO IN Video cable (not included) Back of this unit Y VIDEO OUT S VIDEO OUT Y Y PB PR COMPONENT VIDEO OUT PB VIDEO OUT PR COMPONENT VIDEO OUT PB PR REC OUT The COMPONENT VIDEO OUT terminals can be used for either interlace or progressive output and provide a purer picture than the S VIDEO OUT terminal. Connection using these terminals outputs the colour difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in reproducing colours. [. . . ]