User manual PANASONIC SCZT2

[. . . ] Home Theater Audio System Model No. Operating Instructions SC-ZT2 Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. [. . . ] · Muting is also cancelled when you adjust the volume. Note Adjusting the bass (woofer part) output When you feel the bass volume is not balanced with the volume of the front speakers, you can adjust the bass during playback. 1. Press [CH] to select "WFR ". (The speaker is switched each time you press the button. ) WFR (woofer) RS (surround right) (when used) LS (surround left) (when used) Play 2. Press [SPEAKER LEVEL +, ­] to adjust the bass volume. Adjustment range: MIN, 1 to 15, MAX Adjusting the surround speaker output When using the surround speakers, you can adjust them, too. 1. Press [CH] to select "RS " or "LS ". (The speaker is switched each time you press the button. ) WFR (woofer) RS (surround right) LS (surround left) 2. Press [SPEAKER LEVEL +, ­] to adjust the volume of each speaker. Adjustment range: ­10 to +10 Repeat steps 1 and 2 to adjust the level of each speaker. Note · You cannot adjust the front speakers with this operation. To adjust the volume balance of left and right front speakers, see "Adjusting the volume balance of front speakers". ( page 23) · If the sound is distorted, lower the level. · You cannot adjust the output level of speakers if the sound field effect is off and the speakers' audio output is set to off. ( page 19) · You can adjust the speaker's output level in SFC's each mode respectively. ( page 19) · When a commercially available active subwoofer is connected to the subwoofer output terminal on this unit's rear panel, the subwoofer is synchronized with the unit and the sound volume is adjusted. 22 VQT2R71 Adjusting the surround speaker output using the test signal You can make this setting when using the surround speakers. You can adjust the surround speaker volume by outputting the test signal. Setup menu items "BASS" "TREBLE" "BALANCE" "SPEAKERS" "HDMI" "DUAL PRG" "REMOTE" "EXIT" "DISTANCE" "STB AUDIO" "7. 1CH VS" "SOUND DLY" "ATTENUATOR" "RESET" 1. Press [TEST] to output the test signal. Speaker display L : Front left, R : Front right, RS : Surround right, LS : Surround left · The test signal is output from one speaker at a time for two seconds in the following order. TEST L TEST R TEST RS TEST LS "DRCOMP" "INPUT MODE" 2. Press [VOL +, ­] to adjust the volumes of front speakers to the normal listening level. Adjustment range: 0 (Min) to 50 (Max) · appears only when audio adjustment can be made. · Select "EXIT " and press [OK] to finish the setup mode. Adjusting sound quality Functions and settings You can adjust the level of bass and treble. This setting is effective only when you perform stereo playback of 2-channel analogue and PCM signals (during Dolby Virtual Speaker and Dolby Pro Logic are off). This setting is not displayed in other conditions. Be sure to make the setting in the above condition. 3. Press [CH] to select surround speakers for adjustment. Press [SPEAKER LEVEL +, ­] to adjust each speaker's output level. Adjustment range: RS, LS : ­10 to +10 · The test signal comes from the speaker being adjusted. · The test signal is output again in above the order 2 seconds after adjustment. Repeat steps 3 and 4 to adjust the level of each speaker. 1. [. . . ] VASER, MÅ PLASSERES PÅ APPARATET, * MÅ DU KUN BRUKE ANBEFALT TILBEHØR, * MÅ DU IKKE FJERNE DEKSELET (ELLER BAKSIDEN); INNEHOLDER INGEN DELER SOM BRUKEREN KAN REPARERE. OVERLAT REPARASJONER TIL KVALIFISERTE REPARATØRER. VAROITUS: TULIPALON, SÄHKÖISKUN TAI TUOTTEEN VAURIOITUMISEN RISKIN PIENENTÄMISEKSI: * ÄLÄ ALTISTA TÄTÄ LAITETTA SATEELLE, KOSTEUDELLE, TIPPUVALLE NESTEELLE TAI ROISKEILLE. LAITTEEN PÄÄLLE EI MYÖSKÄÄN SAA LAITTAA NESTEELLÄ TÄYTETTYJÄ ESINEITÄ KUTEN MALJAKOITA. * KÄYTÄ VAIN SUOSITELTUJA LISÄVARUSTEITA. [. . . ]