User manual PANASONIC TH-37LRT12U

[. . . ] Operating Instructions Manual de instrucciones High Definition Hospitality LCD Display Pantalla de LCD de alta definición para la industria hotelera Model No. Número de modelo TH-32LRT12U TH-37LRT12U The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. La ilustración mostrada es una imagen. Antes de conectar, utilizar o ajustar este producto, lea completamente este manual de instrucciones; y guárdelo para consultarlo en el futuro en caso de ser necesario. English Español TQB4CM171 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. [. . . ] If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. · The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. · Some PC models cannot be connected to the set. · There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. · The computer shown in the illustration is for example purposes only. · Additional equipment and cables shown are not supplied with this set. · Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. · Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. · Applicable input signals for Mini D-sub 15P (see page 29). Signal Names for Mini D-sub 15P Connector Pin No. 5 4 10 9 3 8 2 7 1 6 1 2 3 4 Signal Name R (PR/CR) G (Y) B (PB/CB) NC (not connected) GND (Ground) Pin No. 6 7 8 9 10 Signal Name GND (Ground) GND (Ground) GND (Ground) +5 V DC GND (Ground) Pin No. 11 12 13 14 15 Signal Name NC (not connected) SDA HD/SYNC VD SCL 15 14 13 12 11 Pin Layout for PC Input Terminal 5 12 Connections HDMI connection HDMI cable HDMI AV OUT DVD Player or SET-TOP-BOX (HDMI compatible machines only) Note: 1. Additional equipment and HDMI cables shown are not supplied with this set. HDMI Version 1. 2. Audio Out connection Audio equipment R AUDIO OUT L Note: Additional equipment and cables shown are not supplied with this set. 13 Connections Serial Terminals connection The SERIAL terminal is used when the Display is controlled by a computer. COMPUTER RS-232C Straight cable 5 6 4 7 3 8 2 9 1 (Female) D-sub 9p (Male) Pin layout for SERIAL Terminal Notes: · Use the RS-232C straight cable to connect the computer to Signal names for D-sub 9P connector the Display. · The computer shown is for example purposes only. Details · Additional equipment and cables shown are not supplied with 2 RXD this set. 3 TXD 5 The SERIAL terminal conforms to the RS-232C interface GND specification, so that the Display can be controlled by a computer 4·6 Non use which is connected to this terminal. 7·8 Non use The computer will require software which allows the sending 1·9 NC and receiving of control data which satisfies the conditions These signal names are those of computer specifications. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Communication parameters Command Parameter Control details Signal level RS-232C compliant PON None Power ON Synchronization method Asynchronous POF None Power OFF Baud rate 9600 bps AVL ** Volume 00 - 63 Parity None AMT 0 Audio MUTE OFF Character length 8 bits 1 Audio MUTE ON Stop bit 1 bit IMS None Input select (toggle) Flow control RF INPUT RF1 AV1 INPUT AV1 Basic format for control data AV2 AV2 INPUT The transmission of control data from the computer starts with AV3 AV3 INPUT an STX signal, followed by the command, the parameters, and YPbPr YPbPr INPUT lastly an ETX signal in that order. If there are no parameters, HDMI1 HDMI1 INPUT then the parameter signal does not need to be sent. HDMI2 HDMI2 INPUT HDMI3 HDMI3 INPUT STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX PC PC INPUT Colon Parameter(s) End Screen mode select (toggle) DAM None (1-5 bytes) (03h) 16:9 FULL Start 3-character JUST JUST (02h) command (3 bytes) NORM 4:3 Notes With the power off, this display responds to PON · If multiple commands are transmitted, be sure to wait command only. [. . . ] BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. WARRANTY COVERAGE PERIOD EXCEPTIONS Item Video Tape P2/SD Cards Video Heads D5 Video heads Parts 30 days--Replacement only (content not covered) (Content not covered) 1 year or 2, 000 hrs. (prorated) Whichever comes first 1 year or 1, 000 hrs. [. . . ]