User manual PANASONIC TH-42PF20U

[. . . ] de Modelo TH-42PF20U TH-50PF20U Operating Instructions High Definition Plasma Display Contents · Important Safety Instructions . . . . . . . . . . . . . . . . . . 3 · FCC STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 · Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When disconnecting the AC cord, be Note: Make sure that the AC cord is locked on absolutely sure to disconnect the AC both the left and right sides. When using the Wall-hanging bracket (vertical) Note: When using the Wall-hanging bracket (vertical) (TY-WK42PV20), use the holes and to secure the cables. If the clamper is used on the hole , the cables may be caught by the wall-hanging bracket. 1 Attach the clamper hole To remove from the unit: snaps 2 Bundle the cables To loosen: Insert the clamper in a hole. Keep pushing both side snaps hooks Set the tip in the hooks knob Keep pushing the knob 8 Connections Video equipment connection PC IN: PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. (see page 11) SERIAL: Control the Plasma Display by connecting to PC. (see page 12) SLOT: Terminal board (optional accessories) insert slot Note: (see page 5) The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. LAN: Connect to a network to control the unit. (see page 20) Terminals are on the bottom side of the Plasma Display. AV IN (VIDEO): Composite Video Input Terminal (see below) COMPONENT/RGB IN: Component/RGB Video Input Terminal (see below) AV IN (HDMI): HDMI Input Terminal (see page 10) DVI-D IN: DVI-D Input Terminal (see page 10) Connect to video equipment such as VCR or DVD player. VIDEO and COMPONENT / RGB IN connection Note: Additional equipment, cables and adapter plugs shown are not supplied with this set. L R AUDIO OUT VIDEO OUT VCR RCA-BNC Adapter plug RCA-BNC Adapter plug Notes: · Change the "COMPONENT/RGB-IN select" setting in the "SETUP" menu to "COMPONENT" (when COMPONENT signal connection) or "RGB" (when RGB signal connection). · Accepts only RGB signals with "SYNC ON G". DVD Player Y PB PR L R AUDIO OUT Computer Y, PB, PR, OUT RGB Camcorder 9 Connections HDMI connection [Pin assignments and signal names] Pin No. 1 2 3 4 5 6 7 8 9 10 Signal Name T. M. D. S Data2+ T. M. D. S Data2 Shield T. M. D. S Data2T. M. D. S Data1+ T. M. D. S Data1 Shield T. M. D. S Data1T. M. D. S Data0+ T. M. D. S Data0 Shield T. M. D. S Data0T. M. D. S Clock+ Pin No. 11 12 13 14 15 16 17 18 19 Signal Name T. M. D. S Clock Shield T. M. D. S ClockCEC Reserved (N. C. on device) SCL SDA DDC/CEC Ground +5V Power Hot Plug Detect 19 31 HDMI cable 18 42 HDMI AV OUT DVD player Note: Additional equipment and HDMI cable shown are not supplied with this set. DVI-D IN connection PC with DVI-D video out Stereo mini plug (M3) DVI-video cable (Within 5 m) DVI-D Input Connector Pin Layouts Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name T. M. D. S. data 2 shield Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Signal Name +5 V DC Ground Hot plug detect T. M. D. S. data 0 shield 1 9 17 8 16 24 DDC clock DDC data T. M. D. S. data 1 shield Connection port view Notes: · Additional equipment and cables shown are not supplied with this set. · Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or the quality of the cable. T. M. D. S. clock- 10 Connections PC Input Terminals connection (Female) COMPUTER Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Conversion adapter (if necessary) RGB PC cable Mini D-sub 15p (Male) Notes: · With regard to the typical PC input signals that are described in the applicable input signals list, adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list. · Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) · The display resolution is a maximum of 1, 440 × 1, 080 dots when the aspect mode is set to "4:3", and 1, 920 × 1, 080 dots when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. · The PC input terminals are DDC2B-compatible. [. . . ] Whichever comes first 1 year or 1, 000 hrs. Whichever comes first 90 days 1 year 1 year 3 years or 17, 000 hrs. Whichever comes first 3 years or 2, 500 hrs. Whichever comes first 50% of the rated lamp life or 1 year. [. . . ]