User manual PANASONIC TH42PH12EK

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: Bass, Mid, Treble and Surround settings are memorized separately for each Sound Mode. Helpful Hint ( / Normalise Normalisation) While the "Sound" menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. SDI Sound Output This menu is displayed when HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed to the unit. SDI Sound Output Left Channel Right Channel Sound Out Level Meter 2/2 Channel 1 Channel 1 Off Off Item Left Channel Right Channel Sound Out Details Channel 1 to Channel 16 Selects left audio channel. Channel 1 to Channel 16 Selects right audio channel. Disables audio output. Notes: · This menu is available only when selecting a slot that HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TYFB11DHD) is installed. · This menu is unavailable when 2-picture display mode is active. Level Meter Off 1-8ch 9-16ch Sets audio channels to show in the audio level meter. 8 channels are displayed in the audio level meter; 4 channels each on both right and left sides of the display. 1-8ch: Displays the audio level meter (1-8ch) 9-16ch: Displays the audio level meter (9-16ch) 32 PRESENT TIME Setup / Set up TIMER The timer can switch the Plasma Display On or Off. Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary. Then set POWER ON Time / POWER OFF Time. 1 2 Press to display the Setup menu. Press to select Set up TIMER or PRESENT TIME Setup. Press to display the Set up TIMER screen or PRESENT TIME Setup screen. Setup MULTI DISPLAY Setup MULTI PIP Setup Portrait Setup Set up TIMER PRESENT TIME Setup Network Setup Display orientation 2/2 Landscape PRESENT TIME Setup 1 Press to select DAY or PRESENT TIME. PRESENT TIME Setup PRESENT TIME MON 99:99 Press to setup DAY or PRESENT TIME. Set button: Forward MON DAY button: Back 99:99 PRESENT TIME Notes: · Pressing " " or " " button once changes PRESENT TIME 1 minute. To stop the Screensaver under On, press the R button or any buttons on the main unit. Note: When the display is turned off, the Scrensaver will be deactivated. 34 Screensaver (For preventing image retention) Setup of Screensaver Time After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when "Mode" is "On" or "Off". ) Press to select Start Time / Finish Time (when Time Designation is selected). Press to select Periodic Time / Operating Time (when Interval is selected). Press to select Screensaver duration (when Standby after SCR Saver is selected). button: Forward button: Back Screensaver PRESENT TIME Start Function Mode Start Time Finish Time 15:00 Scrolling bar only Time Designation 6:15 12:30 Screensaver PRESENT TIME Start Function Mode Periodic Time Operating Time Scrolling bar only Interval 12:00 3:00 15:00 Notes: · Pressing " " or " " button once changes the Time 1 minute. [However, switching occurs every 15 minutes when Periodic Time is selected. ] · Pressing " " or " " button continuously changes the Time by 15 minutes. · "Screensaver duration" of the "Standby after SCR Saver" can be set from 0:00 to 23:59. When this is set to "0:00", " Standby after SCR Saver" will not be activated. Note: Timer function will not work unless "PRESENT TIME" is set. Screensaver PRESENT TIME 15:00 Start Scrolling bar only Function Standby after SCR Saver Mode 6:15 Screensaver duration 35 Reduces screen image retention Extended life settings The following settings are setup to reduce image retention: Setup Signal Screensaver Extended life settings Input label Component/RGB-in select Power save Standby save PC Power management DVI-D Power management Auto power off OSD Language RGB Off Off Off Off Off English (UK) 1/2 Extended life settings Express settings Custom settings Reset Set to the recommended value Set individually Reset to the factory settings Extended life settings Recommended settings Picture Mode Contrast Side panel NANODRIFT Saver Peak limit Lock settings Apply to current input Apply to all inputs Dynamic 30 High High mid Off unlock Image Retention Reduction Menu Image Retention Reduction Menu "Extended life settings" enables you to set the following 5 menus (Image Retention Reduction Menu) as recommended values or set them individually. Picture Mode Contrast "Picture Mode" and "Contrast" are same as "Picture" menu items (see page 27). [. . . ] 2 Press the Volume Up"+" or Down"­" button to select "OSD Language". 3 Press and hold the ENTER button till the Shipping menu is displayed. 4 Press the Volume Up"+" or Down"­" button to select "YES". 5 Press the ENTER button and wait for 10 sec. 67 Command list of Weekly Command Timer No. [. . . ]