User manual PANASONIC TH-42PRT12U

[. . . ] Operating Instructions Manual de instrucciones 42" High Definition Hospitality Plasma Display Pantalla de plasma de alta definición de 42" para la industria hotelera Model No. Número de modelo TH-42PRT12U The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. La ilustración mostrada es una imagen. Antes de conectar, utilizar o ajustar este producto, lea completamente este manual de instrucciones; y guárdelo para consultarlo en el futuro en caso de ser necesario. English Español TQB4CM161 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. [. . . ] Remove the pedestal. A A Remove the four screws. Pull out the pedestal. B B Foam mat or thick soft cloth A · · · · WARNING Failure to use a Panasonic bracket or choosing to mount the unit yourself will be done at the risk of the consumer. Any damage resulting from not having a professional installer mount will void your unit's warranty. Always be sure to ask a qualified technician to carry out set-up. Incorrect fitting may cause equipment to fall, resulting in injury and product damage. Do not mount this Plasma display directly below ceiling lights (such as spotlights, floodlights, or halogen lights) which typically give off high heat. Doing so may warp or damage plastic cabinet parts. 10 Accessories Optional Accessory / AC Cord Connection Optional Accessory · Note: · In order to maintain the Plasma display's performance and safety, be absolutely sure to ask your dealer or a licensed contractor to secure the wall-hanging brackets. · Carefully read the instructions accompanying the Plasma display stand or pedestal, and be absolutely sure to take steps to prevent the Plasma display from tipping over. · Handle the Plasma display carefully during installation since subjecting it to impact or other forces may cause its panel to crack. Wall-hanging bracket (angle) TY-WK4P1RW · AC Cord Connection To attach To remove Insertitfirmlyuntilthe tabs on both sides click into place. Keep pushing both side snaps and pull down. 11 Connections Optional terminal Component (YPbPr) connection (see page 13) Audio out connection (see page 16) AV connection (see page 13) Serial Terminals connection (see page 15) PC input terminals connection (see page 14) HDMI connection (see page 16) Left side Back side 12 Connections AV connection Example of input signal source S VIDEO VCR S VIDEO OUT CAMCORDER VIDEO OUT AUDIO OUT L R VCR Back side Left side Notes: · Additional equipment and cables shown are not supplied with this set. · If S Video and Video devices are both connected, the S Video input signal is the priority source. Component (YPbPr) connection Example of input signal source DVD COMPONENT VIDEO OUT Y Y, PB, PR, PB OUT PR Digital TV-SET-TOP-BOX (DTV-STB) L AUDIO OUT R Note: Additional equipment and cables shown are not supplied with this set. 1 Connections PC Input Terminals connection COMPUTER (Female) Conversion adapter (if necessary) RGB PC cable Mini D-sub 15p (Male) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Notes: · Computer signals which can be input are those with a horizontal scanning frequency of 15 to 79. 97 kHz and vertical scanning frequency of 48 to 75 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) · The display resolution is a maximum of 768 x 768 dots when the aspect mode is set to "4:3" and 1, 024 x 768 dots when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. · The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. · Some PC models cannot be connected to the set. · There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. · The computer shown in the illustration is for example purposes only. · Additional equipment and cables shown are not supplied with this set. · Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. · Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. · Applicable input signals for Mini D-sub 15P (see page 31). Signal Names for Mini D-sub 15P Connector 5 4 10 9 3 8 2 7 1 6 Pin No. 1 2 3 4 5 Signal Name G B NC (not connected) GND (Ground) Pin No. 6 7 8 9 10 Signal Name GND (Ground) GND (Ground) GND (Ground) +5 V DC GND (Ground) Pin No. 11 12 13 14 15 Signal Name NC (not connected) SDA HD/SYNC VD SCL 15 14 13 12 11 Pin Layout for PC Input Terminal 14 Connections SERIAL Terminals connection The SERIAL terminal is used when the Display is controlled by a computer. COMPUTER RS-232C Straight cable 5 6 4 7 3 8 2 9 1 D-sub 9p (Female) Pin layout for SERIAL Terminal Notes: (Male) · Use the RS-232C straight cable to connect the computer to Signal names for D-sub 9P connector the Display. [. . . ] Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. [. . . ]