User manual PANASONIC TH-R65PY800

[. . . ] Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Operating Instructions Plasma Television TH-R65PY800 TH-42PV600E TH-50PV600E Model No. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Licence Trademark Credits VGA is a trademark of International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, USA. [. . . ] Photos cannot be deleted or locked. To display the operation guide Volume · · Videos Pause Playback Fast forward (hold down) To next video Stop Photos (operate in step Display the menu or 5 ) Select "Viewing setup" M ai n m en u P i ctu re m en u next Select the functions and access select Viewing setup Slide show Interval Repeat Access 5sec Off Advanced To return to TV Exit SD : Return Rewind (hold down) To previous video To return to · Menu Item Slide show Interval Repeat Vi ew in g setu p "Picture menu" (p. 16) select set the SD menu Photos To previous photo To thumbnail Rotate 90° (clockwise) To next photo Select List Adjustments / Configurations (alternatives) Start slide show To stop in mid-cycle Operation guide Zoom SD : Return Exit red ZOOM · · 22 Caution To change the aspect ratio Displayed one at a time Rotate 90° (anti-clockwise) · · Viewing setup During zoom mode, you can move the position by using the cursor buttons. Select slide show interval (5 / 10 / 15 / 30 / 60 / 90 / 120sec) Slide show repeat (Off / On) During the playback, no signals are output from the monitor output terminals. "Date" shows the date on which the recording was made by this unit, DIGA or D-snap. Its format is 01/01/2000 when recordings are made without date signal. 23 Recording a Programme on SD Card The TV channels and AV1 input signals (PAL / SECAM) can be recorded on the SD card. During recording, it is possible to watch other terminals input signal. To set the recording time and mode / To format the card Select the SD mode Set Setup 1 2 select Economy No setting Access Insert the SD Card (p. 23) Rec mode Rec time Card format Select "Setup" SD card set select MP E G 4 v ie w While watching a programme P hoto v ie w S e tup Me mory le ft next · Should such a message appear Start recording? Not enough memory Current setting Rec time 180min Rec mode Economy Recordable at 15min · · Recordable time is displayed if the recording time is not set. 25) Start recording Cancel Card capacity is not enough. Menu Item Adjustments / Configurations Select image quality (Extra fine / Super fine / Fine / Normal / Economy) The quality of audio is not changed. Multi Media Cards do not support the Extra fine and Super fine recording mode. If the recording is started in these status, recording will automatically be performed in the Fine mode. · Recording a Programme on SD Card Rec mode · · Continue (Recording is stopped when the card capacity is full. ) Cancel · · · · Setup menu Rec time Select recording time (No setting / 5 / 10 / 15 / 30 / 60 / 90 / 120 / 180min) No setting : Recorded until the Card capacity is full Format the card inserted in the SD Card slot (all data is erased) Do not remove the SD card while formatting. That may cause the card not to be able to record properly. 3 TV To stop Card format (During the confirmation message appears) To check memory left You can confirm the remaining time for recording in each Rec mode. Select the SD mode · · · · · · · · · Note You cannot record the copy protected signals. Select the input mode to HDMI1 or HDMI2 (p. 12), and make sure that an image is displayed correctly. Features available Some recording equipments are not applicable. Read the manuals of the equipment. Direct TV Recording: Recording the current programme in VCR / DVD recorder immediately. 1 2 3 4 Easy playback Display the menu What you see is What you record · · · When Direct TV Recording is performed, the recording equipment is automatically turned on if it is in Standby mode. The recording equipment is recording from its own tuner. You can turn the TV off during recording. Do not turn the TV off during recording AV source. Otherwise the recording will be stopped. Select "Setup menu" Main menu Home theatre Picture menu Sound menu Setup menu next select · External Equipment Select "Control with HDMI" Setup menu Q-Link AV2 out Control with HDMI Teletext Off timer Text language Side panel Power save Tuning menu OSD language AV2 TV On TOP Off West Off Off select Select "On" (default is On) select Information / Message Recording information or if recording is not possible, a message is displayed. (Only when the programme number is "0" or "AV mode" for some equipment. ) Advanced Automatic Input switching-When the connected Panasonic equipment is operated, input mode is switched automatically. When it is stopped operating, input mode is returned. You can control the theatre speaker with TV's remote control. This function is available when Panasonic Amplifier or Player theatre is connected. Power on link and Easy playback Insert a videocassette or DVD in the recording equipment and it is operated, TV is turned on and input mode is switched automatically so that you can view the content. (Only when TV is in Standby mode. ) Display the menu Select "Home theatre" or "TV speaker" Home theatre: Theatre speaker Main menu Home theatre Picture menu Sound menu Setup menu Adjustment for equipment (automatically turned on if it is in Standby mode) Volume up / down Mute set select Power off link When TV is set to Standby mode, the recording equipment is also automatically set to Standby. [. . . ] Set "Control with HDMI" to "Off", then set to "On" again. 27) SD A pixel or luminescent spot may occasionally be missing in plasma displays. (Not a faulty symptom) Contact the authorized Service Centre. FAQs, etc. The remote control does not work TV · · The sleep function is activated. The TV unit enters "Standby mode" about 30 min. [. . . ]