User manual PANASONIC TX29AD1P

[. . . ] Do not pull the power cable to remove the mains plug from the socket, always remove it by the plug. D Adequate ventilation is essential to prevent failure of electrical components. We recommend that a gap of at least 5cm is left all around this TV even when it is placed inside a cabinet or between shelves. D GENERAL INFORMATION Sleep Feature If the set is not switched off when the TV station stops transmitting , it will automatically go to standby mode after 30 minutes. This function will not operate when in AV mode. Last Position Memory Certain functions have a last position memory, i. e. the setting at the time of switch off will be the setting used when the receiver is switched on again: Programme position Colour Volume Contrast Brightness Standby Sharpness Status C---A---T---S 3 ACCESSORIES Check that you have the accessories and items shown Remote Control Transmitter EUR511300 Operating Instruction book Batteries for the Remote Control Transmitter. [. . . ] (2 x R6 (UM3) size) Telescopic Antenna (TX---14JT1C/V) TSA---120026 FITTING REMOTE CONTROL BATTERIES 1 2 3 Slide off the battery cover Insert batteries --- note correct polarity Replace the cover D Make sure that the batteries are fitted the correct way round. D Do not mix old batteries with new batteries. Remove old, exhausted batteries immediately. D Do not mix different battery types, i. e. Do not use rechargeable (Ni---Cad) batteries. 4 INSTALLATION AND SET---UP 1 TV only Connect Aerial co---axial cable direct to TV RF IN socket. OR USING A VCR Connect aerial co---axial cable to RF Input socket of VCR and a RF co---axial cable from VCR RF Out socket to TV RF IN socket. The VCR can also be connected to the TV using a SCART to SCART lead. VCR Further details of Audio/ Video connections can be found on page 11. Ancillary equipment and leads are not supplied. 2 Switch ON your VCR. *1 Plug the TV into a mains socket and switch ON. Programmes will appear immediately if your dealer has programmed the TV for you. *1 We recommend that you switch ON the VCR's test signal --- refer to your VCR instruction book. 5 INSTALLATION AND SET---UP 3 Choose the desired language from the OSD language selection. Press TV/AV button to start ATP . 4 TV stations will be located, sorted into order and stored ready for use. *1 CH02 OSD Language D GB F I E S NL ---/+ : Adjust TV/AV : Start ATP N : Exit 02 99 : 21 41 ATP 5 The first available channel displayed. Press the F key (Front panel) until "Manual Tuning" is reached. Press --- or + to access "Manual Tuning". 1 CH21 Manual Tuning TV/AV ---/+ STR F, N : : : : Prog. Start Search Store Exit 02 99 : 21 41 Store Function select / Exit Change programme position Search 9 TELETEXT OPERATION D Teletext functions may vary depending on the broadcasting companies and are only available if the selected channel is transmitting Teletext. D If button "F" is pressed in the Teletext mode the blue contrast scale will appear; press buttons "+" and "---" to change the settings. D When in Teletext mode, the volume may still be adjusted by pressing buttons "+" or "---". What is FLOF (FASTEXT)? In the FASTEXT mode four differently coloured subjects are shown at the bottom of the screen matching the colour of the buttons on your remote control unit. To access more information about one of these subjects, press the appropriately coloured button. This function allows quick access to information on the subject shown. TV/TEXT TV/Teletext Mode Press button TV/TEXT. The Teletext title page will be displayed on the screen. Press again to return to the TV mode. INDEX Index Press this button to return to the main index page. Depending on the status you may have to press a few times to return to the main index page. HOLD Hold Press to hold the current page. Press again to cancel the hold. TIME TEXT Time/Text When Teletext information exceeds more than one page, it may take some time for the automatic changing of the sub pages to reach the sub page you require. [. . . ] Press again to cancel the hold. TIME TEXT Time/Text When Teletext information exceeds more than one page, it may take some time for the automatic changing of the sub pages to reach the sub page you require. Press the TIME TEXT button; **** will be displayed at the top left of the screen. To select sub---page 5, enter 0, 0, 0 and 5. The TV is now searching for the correct sub page. [. . . ]