User manual PANASONIC TX36PF10P

[. . . ] This TV has a low power consumption making it very cost effective to run. Also, when in Standby mode the power consumption is merely 1, 2W. This instruction book is produced using recycled paper. Analogue and Digital television --- what are they? [. . . ] has previously been set, enter the required 4 digit Owner I. D. PIN NUMBER, using 0 to 9 on the remote control (4). If a 4 digit PIN NUMBER was entered above, you will be taken automatically to the NAME line. Repeat above until NAME, HOUSE NUMBER and POSTCODE are entered. Press OK again, to confirm, when asked, "Are you sure ?" (5). Return - For future reference, write your PIN Number here : 22 MANUAL TUNING --- FRONT PANEL CONTROLS Manual tuning of the analogue programme positions is available from the front panel controls The Front panel controls are located under the flap on the front of the TV. 1 (1) F (2) - /v (3) Select an existing analogue programme position. Press the F button (1) repeatedly until "Tuning mode" is reached. Press the - or + button (2) or (3) to access Manual tuning (Front panel). Press --- or + (2) or (3), to begin searching for stations. The television will begin to search for stations. When a station is found the search will pause; if it is not the correct station, you can press the --- or + buttons (2) or (3) to continue searching. (4) TV/AV (5) STR Important note : On passing channel 68, tuning will restart at channel 21. 21 68 When the desired station is found, press the TV/AV button (4) to move to the programme position indicator. Press --- or +, (2) or (3) to select the programme position in which the station is to be stored. When receiving DVB radio services for example, the brightness and contrast of the screen will be reduced. To cancel either screensaver, press any button. Changes made within the DVB---Setup menu will cause settings to change from "Default" to "User defined". To return to the default settings for this TV, select "Default" using the left or right cursor key (3), then press OK (5) to store your setting. Common Interface Module Favourites Setup Preferred Subtitles System Update Display Timeout 0 (no display) ~ 10 Screensaver Active Settings 24 COMMON INTERFACE MODULE MENU The Common Interface Module menu provides access to software contained on Common Interface (CI) Modules. These can be inserted in the "CI" slot located at the rear of the TV. IMPORTANT NOTES: Switch off the TV using the front panel switch before inserting or removing a module. If you are installing a TV software update, please follow the dedicated instructions supplied with the module. Insert the CI module as described below: Some Common Interface Modules may be a two piece design consisting of a card reader together with the viewing card. When using this design of card, first insert the card reader firmly into the CI slot on the TV (flap side to the left). Secondly, insert the viewing card into the reader. TV Insert flap Viewing card Card reader side to the left ! Switch on the TV. Using the Menu button (1), open the Main Menu. [. . . ] The purchaser will then be informed whether i ii iii The sales company or national distributor will handle the repair service or The sales company or national distributor will arrange for trans-shipment of the appliance to the EU/EEA country or Turkey where the appliance was originally marketed, or the purchaser may himself send the appliance to the sales company or national distributor in the EU/EEA country or Turkey where the appliance was originally marketed B. If the appliance is a product/model which is normally supplied by the sales company or national distributor in the country where it is used by the purchaser, then the appliance together with the guarantee and proof of date of purchase, should be returned at the purchaser's risk and expense to such sales company or distributor, which will handle the repair service. In some countries, the affiliated sales company or national distributor will designate dealers or certain service centres to execute the repairs involved. If the appliance is a product/model which is not normally supplied in the country where used, or if the appliances internal or external product characteristics are different from those of the equivalent model in the country where used, the sales company or national distributor may be able to have the guarantee repair service executed by obtaining spare parts from the country where the appliance was originally marketed, or it may be necessary to have the guarantee repair service executed by the sales company or national distributor in the country where the appliance was originally marketed. [. . . ]