User manual PANASONIC TYEW3D10E

[. . . ] Stop using the 3D Eyewear immediately if you feel tired, discomfort, or any other uncomfortable sensation. Take an appropriate break after viewing a 3D movie. Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games or computers. Be careful not to strike the television screen or other people unintentionally. [. . . ] ( page 7) Infra-red receiver Receives infra-red signals from the television. The liquid crystal shutter open/close timing is controlled by receiving infra-red signals from the television, which provide 3D expression of the images. If the eyewear stops receiving infra-red signal from the television, the power automatically switches off after 5 minutes. Nose pad installation section (3D Eyewear inner section) ( page 7) Specialised band can be attached here. ( page 7) Liquid Crystal Shutter (lens) Controls the images for 3D viewing. The left and right liquid crystal shutters are alternately opened and closed in time with the left side and right side images that are alternately displayed on the television to achieve the 3D effect. Power button (bottom side of 3D Eyewear) Switches on the 3D Eyewear power. Press and hold the power button for approximately 1 second to switch the power on, and the indicator lamp lights for approximately 2 seconds. (When the battery is low, the indicator lamp flashes 5 times on switching on the power. ) To switch the power off, press and hold the power button for approximately 1 second. The indicator lamp flashes 3 times, then the power switches off. Indicator lamp Power button 6 - ENGLISH Using for the first time Remove the insulating sheet Attach the specialised band If the 3D Eyewear slips out of place, use the specialised band included to hold it in place. Specialised band Attach the band to the left and right tips of the frame, and adjust the length. Insulating sheet Attach the nose pad If required, use the included nose pad. Nose pad A adjusts the attachment position of the 3D Eyewear between 2 vertical levels. (Slot 2 of the 3 protrusions on the 3D Eyewear into the holes on nose pad A. ) When using nose pad B, ensure that all 3 protrusions on the 3D Eyewear are inserted into the 3 holes on nose pad B. Make sure that the nose pad is inserted all the way and securely attached. Nose pad A Accessories < > indicates the quantity. 3D Eyewear case ·······················<1> Specialised band························<1> Nose pad A/B ·····························<1> A B When the end of the specialised band is straightened, form a loop at the end of the band, and fix the twisted part. Select the nose pad that suit you from A and B. It is recommended to wear the 3D glasses over correction glasses without the nose pad. ENGLISH - 7 Using the 3D Eyewear Using the television menu controls, set so that 3D images are shown. 1. (When 3D image signals are being received) press the MENU button on the television remote control. Select "Setup", and press the OK button. Select "3D settings", and press the OK button. Select "3D Picture Display", and use to select "3D" or "2D". The procedure above is only an example. For details, see the television operating instructions. Wearing the 3D Eyewear If the 3D Eyewear slips out of place, hold it in place using the specialised band, and adjust the length of the band. ( page 7) If the 3D images are not displayed correctly, adjust the 3D image-related settings. For details, see the television operating instructions. * The perceived three dimensional effects of the 3D Eyewear differ from person to person. 1. Press and hold the power button on the 3D Eyewear for approximately 1 second. [. . . ] Are the left and right sides of the 3D image reversed?Switch the left and right sides of the 3D image. For details, see the television operating instructions. The battery is too low to operate the 3D Eyewear. [. . . ]